Pitney Bowes J693 manual

Page 105

alphanumeric Consisting of alphabetic, numeric, punctuation and other symbols.

backing material The silicon-coated paper carrier material to which labels with adhesive backing are affixed. Also referred to as “liner”.

bar code A representation of alphanumeric information in a pattern of machine-readable marks. The basic categories are divided into one-dimensional (UPC, Code 39, Postnet, etc.) and two- dimensional barcodes (Data Matrix, MaxiCode, PDF417, etc.).

boot loader The resident program that loads the application from Flash memory, decompresses it into the SRAM, and starts operations.

calibration The process through which sensor readings are entered into the printer for correct sensor function (e.g., detection of a given media) and TOF positioning.

character set The entire complement of alphanumeric symbols contained in a given font.

checksum An alphanumeric error detection method used in many bar code symbologies for informational security.

continuous media An uninterrupted roll or box of label or tag stock media that contains no gap, notch, or mark to separate individual labels or tags.

core diameter The inside diameter measurement of the cardboard core at the center of a ribbon or media roll.

cutter A mechanical device (e.g., rotary or guillotine) used to cut labels or tags following printing.

defaults The functional setting values returned following a factory reset of the printer.

J693

95

Image 105

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedAdjusting and Maintaining the Printer TroubleshootingSpecifications Appendix B Appendix aAppendix C Appendix DPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Indicator Lights LCD DisplayLiquid Crystal Display Level 1 Reset Resetting the PrinterNavigating the Menu System Enter Password Keep Host CHANGES?Enter = YES Media Type Media SettingsSensor Type Label LengthPrint Control Modules Present SensorCutter Gpio Port GpioEND of Print System Settings Upgrade Printer Configuration LevelPrinter KEY CodeSET Factory Defaults Imaging ModeFormat Attributes Security Pause ModeUnits of Measure Allegro EmulationSerial Port a CommunicationsSerial Port B Parallel Port aTimeout Host SettingsFeedback Mode Control CodesOptions Testing HEX Dump ModeTest Sensor ReadingsUnderstanding the Display Messages User Prompts and Condition MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Positioning Calibration Media Sensor CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Die-cut stock remove Notched stock placeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Application Update Problems Application Update Error MessagesDescriptions / Causes / Solutions Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Bar Codes Printer SpecificationsFonts ElectricalPrinting Specifications Environmental RequirementsMechanical Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsJ693 Function Speed Range Default Setting Speed Settings and DefaultsPrint FeedRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693