Pitney Bowes J693 manual Configuration Level, Printer KEY, Upgrade Printer, Code

Page 35

System Settings (continued)

CONFIGURATION LEVEL		To upgrade the application (resident
		software) of the printer, the hardware and
		software compatibility levels must match for
		the update to be accepted. This information is
		displayed here and can also be found printed
		on the configuration label.
	PRINTER KEY	Each printer has a unique KEY number in the
		following form:
			vvvv-wwxx-yyyyyy-zzz
		where:
		vvvv – represents the model number of the
		vvvv – represents the model number of the
			application loaded
		wwxx – represents the configuration level
			ww represents the main board
			hardware compatibility
			level
			xx represents the software
			compatibility level (see
			below)

		yyyyyy –	is a manufacturing date code
		zzz –	is a unique time stamp

	UPGRADE PRINTER	The application version may only be updated
	CODE	with a configuration level of equal or lesser
		value than the software level; however, the
		printer’s software compatibility level can be
		increased by purchasing and entering the
		proper upgrade code here.

(Continued next page)

J693

25

Image 35

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Getting Started Setting Up the PrinterUsing the Front Panel Printer OverviewSpecifications Adjusting and Maintaining the PrinterTroubleshooting Appendix D Appendix aAppendix B Appendix CPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Liquid Crystal Display Indicator LightsLCD Display Level 1 Reset Resetting the PrinterNavigating the Menu System Enter = YES Enter PasswordKeep Host CHANGES? Label Length Media SettingsMedia Type Sensor TypePrint Control Cutter ModulesPresent Sensor END of Print Gpio PortGpio System Settings Code Configuration LevelUpgrade Printer Printer KEYFormat Attributes SET Factory DefaultsImaging Mode Allegro Emulation Pause ModeSecurity Units of MeasureParallel Port a CommunicationsSerial Port a Serial Port BControl Codes Host SettingsTimeout Feedback ModeSensor Readings HEX Dump ModeOptions Testing TestDescription Conditions Understanding the Display MessagesUser Prompts and Condition Messages User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Standard Calibration Positioning CalibrationMedia Sensor Calibration Step Operator Action Displayed Message Comment Press the key to Reflective media place Die-cut stock removeNotched stock place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Descriptions / Causes / Solutions Application Update ProblemsApplication Update Error Messages Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Electrical Printer SpecificationsBar Codes FontsMechanical Printing SpecificationsEnvironmental Requirements Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsFeed Speed Settings and DefaultsJ693 Function Speed Range Default Setting PrintRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693