Pitney Bowes J693 manual Copyright Information, Firmware Software Agreement

Page 3

Copyright Information:

CG Triumvirate is a trademark of Agfa Corporation.

CG Times based upon Times New Roman under license from the Monotype Corporation.

Firmware (Software) Agreement

The enclosed Firmware (Software) resident in the Printer is owned by Licensor or its suppliers and is licensed for used only on a single printer in the user’s Trade or Business.

The User agrees not to, and not to authorize or permit any other person or party to duplicate, or copy the Firmware or the information contained in the non-volatile or programmable memory. The firmware (Software) is protected by applicable copyright laws and Licensor retains all rights not expressly granted. In no event will Licensor or its suppliers be liable for any damages or loss, including direct, incidental, economic, special, or consequential damages, arising out of the use or inability to use the Firmware (Software).

Information in this document is subject to change without notice and does not represent a commitment on the part of Pitney Bowes. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser's personal use, without the expressed written permission of Pitney Bowes.

All rights reserved. Printed in the United States of America.

Part Number: 88-2271-01

J693 - SV60824

Revision: B

Image 3

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Getting Started Setting Up the PrinterUsing the Front Panel Printer OverviewAdjusting and Maintaining the Printer TroubleshootingSpecifications Appendix D Appendix aAppendix B Appendix CPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Indicator Lights LCD DisplayLiquid Crystal Display Level 1 Reset Resetting the PrinterNavigating the Menu System Enter Password Keep Host CHANGES?Enter = YES Label Length Media SettingsMedia Type Sensor TypePrint Control Modules Present SensorCutter Gpio Port GpioEND of Print System Settings Code Configuration LevelUpgrade Printer Printer KEYSET Factory Defaults Imaging ModeFormat Attributes Allegro Emulation Pause ModeSecurity Units of MeasureParallel Port a CommunicationsSerial Port a Serial Port BControl Codes Host SettingsTimeout Feedback ModeSensor Readings HEX Dump ModeOptions Testing TestUnderstanding the Display Messages User Prompts and Condition MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Positioning Calibration Media Sensor CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Die-cut stock remove Notched stock placeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Application Update Problems Application Update Error MessagesDescriptions / Causes / Solutions Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Electrical Printer SpecificationsBar Codes FontsPrinting Specifications Environmental RequirementsMechanical Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsFeed Speed Settings and DefaultsJ693 Function Speed Range Default Setting PrintRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693