Pitney Bowes J693 manual Ribbon Removal, Ribbon routing path

Page 21

p

Mount the ribbon so that it is dispensed in the appropriate direction for the

qribbon type.

Slide the ribbon on completely to rest against the flange.

r

sRoute the ribbon under the Ribbon Roller then out the front of the printer.

Continue routing the ribbon up to and around the Ribbon Take-Up Hub, as shown. Wind the ribbon around several times in a clockwise direction to

tsecure it in place.

Lower the printhead and rotate the Printhead Latch back to the locked

uposition. Close the Access Cover.

With the printer ‘On’ press and hold the FEED button for three seconds to position the labels for printing; see Section 5.2 for details.

Ribbon routing path

Ribbon Removal:

Pull the empty core from the Ribbon Supply Hub and discard it. Next, grasp the used ribbon on the Ribbon Take-Up Hub, while gently pulling out on the hub, compress the hub to pull off the used ribbon.

J693

11

Image 21

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedAdjusting and Maintaining the Printer TroubleshootingSpecifications Appendix B Appendix aAppendix C Appendix DPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Indicator Lights LCD DisplayLiquid Crystal Display Level 1 Reset Resetting the PrinterNavigating the Menu System Enter Password Keep Host CHANGES?Enter = YES Media Type Media SettingsSensor Type Label LengthPrint Control Modules Present SensorCutter Gpio Port GpioEND of Print System Settings Upgrade Printer Configuration LevelPrinter KEY CodeSET Factory Defaults Imaging ModeFormat Attributes Security Pause ModeUnits of Measure Allegro EmulationSerial Port a CommunicationsSerial Port B Parallel Port aTimeout Host SettingsFeedback Mode Control CodesOptions Testing HEX Dump ModeTest Sensor ReadingsUnderstanding the Display Messages User Prompts and Condition MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Positioning Calibration Media Sensor CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Die-cut stock remove Notched stock placeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Application Update Problems Application Update Error MessagesDescriptions / Causes / Solutions Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Bar Codes Printer SpecificationsFonts ElectricalPrinting Specifications Environmental RequirementsMechanical Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsJ693 Function Speed Range Default Setting Speed Settings and DefaultsPrint FeedRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693