Pitney Bowes J693 manual Module Assignments, Print Resolutions and Maximum Widths

Page 97

&

Module Assignments

Memory Module

	Designator	Module Size	Volatile*	Location / Use

	A	Future Option	N/A	N/A
	B	Future Option	N/A	N/A
	D	1024 KB	Yes	Main PCB SDRAM – user
	D	(default size)		addressable for graphics, fonts, and
		(default size)		addressable for graphics, fonts, and
				label formats
	F	4 MB	No	Optional Flash Card – user
				addressable for graphics, fonts, and
				label formats
	Y	64 KB	No	Main PCB Flash – reserved for
				EFIGS
	Z	4 MB	No	Optional Flash Card – reserved for
				ILPC

*When power is removed from the printer, stored data will be lost.

Print Resolutions and Maximum Widths

Resolutions and Widths

	Model	Printhead Resolution	Maximum Print		Factory Default
	Model	Printhead Resolution		Width	Setting
				Width	Setting
			Inches	Millimeters
	J693	203 dots/inch	4.09	103.9	4.10
		(8 dots/mm)

J693

87

Image 97

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedTroubleshooting Adjusting and Maintaining the PrinterSpecifications Appendix B Appendix aAppendix C Appendix DPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels LCD Display Indicator LightsLiquid Crystal Display Level 1 Reset Resetting the PrinterNavigating the Menu System Keep Host CHANGES? Enter PasswordEnter = YES Media Type Media SettingsSensor Type Label LengthPrint Control Present Sensor ModulesCutter Gpio Gpio PortEND of Print System Settings Upgrade Printer Configuration LevelPrinter KEY CodeImaging Mode SET Factory DefaultsFormat Attributes Security Pause ModeUnits of Measure Allegro EmulationSerial Port a CommunicationsSerial Port B Parallel Port aTimeout Host SettingsFeedback Mode Control CodesOptions Testing HEX Dump ModeTest Sensor ReadingsUser Prompts and Condition Messages Understanding the Display MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Media Sensor Calibration Positioning CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Notched stock place Die-cut stock removeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Application Update Error Messages Application Update ProblemsDescriptions / Causes / Solutions Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Bar Codes Printer SpecificationsFonts ElectricalEnvironmental Requirements Printing SpecificationsMechanical Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsJ693 Function Speed Range Default Setting Speed Settings and DefaultsPrint FeedRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693