Pitney Bowes J693 manual Agency Compliance and Approvals

Page 4

Agency Compliance and Approvals:

UL1950 Information Technology Equipment

C22.2 No. 950-M93

C US Listed

EN60950

For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting of a min H05VV-F cord which has a minimum 0.75 square mm diameter conductors, provided with an IEC 320 receptacle and a male plug for the country of installation rated 6A, 250V

Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250 Volt.

As an Energy Star Partner, the manufacturer has determined that this product meets the Energy Star guidelines for energy efficiency.

The manufacturer declares under sole responsibility that this product conforms to the following standards or other normative documents:

EMC: EN 55022 (1993) Class B

EN 50024 (1998)

EN 45501 (1992)

Safety: This product complies with the requirements of EN 60950/All:1997

Gost-R

FCC: This device complies with FCC CFR 47 Part 15 Class A.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Image 4

Contents J693 Page Copyright Information Firmware Software AgreementAgency Compliance and Approvals Important Safety Instructions Page Setting Up the Printer Using the Front PanelPrinter Overview Getting StartedTroubleshooting Adjusting and Maintaining the PrinterSpecifications Appendix a Appendix BAppendix C Appendix DPage About this Printer Standard Features PrintingInspection J693 Installing the Printer Communications Interfacing Serial PortLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon Removal Ribbon routing pathJ693 Ready Mode Normal Operation Ready Light ‘On’ Operating the Front PanelMenu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels LCD Display Indicator LightsLiquid Crystal Display Resetting the Printer Level 1 ResetNavigating the Menu System Keep Host CHANGES? Enter PasswordEnter = YES Media Settings Media TypeSensor Type Label LengthPrint Control Present Sensor ModulesCutter Gpio Gpio PortEND of Print System Settings Configuration Level Upgrade PrinterPrinter KEY CodeImaging Mode SET Factory DefaultsFormat Attributes Pause Mode SecurityUnits of Measure Allegro EmulationCommunications Serial Port aSerial Port B Parallel Port aHost Settings TimeoutFeedback Mode Control CodesHEX Dump Mode Options TestingTest Sensor ReadingsUser Prompts and Condition Messages Understanding the Display MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Printing from the Quick Test Mode Print Quality LabelConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label Validation Label User Defined LabelMedia Sensor Adjustment Media Type Sensor Type Sensor Eye Mark PositionPage Media Sensor Calibration Positioning CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Notched stock place Die-cut stock removeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Printhead Adjustments Burn Line AdjustmentPage Printhead Replacement Cleaning Schedule Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead In5.5.2 Cleaning the Platen Roller Cleaning Interior and Exterior Surfaces Updating the Application ProgramUpdating from the Ready Mode Updating from the Download Mode Application Update Error Messages Application Update ProblemsDescriptions / Causes / Solutions Updating the Boot Loader Program J693 Troubleshooting Tips If experiencing this problem… Try this solution…If experiencing this problem… Try this solution… If an image is on the used ribbon If no image is on the used ribbonIf experiencing this problem… Fault and Warning Messages Description Possible SolutionsFault Messages Ribbon supply hub If media is moving If media is not movingDescription Action Hex Dump Mode Printer Specifications Bar CodesFonts ElectricalEnvironmental Requirements Printing SpecificationsMechanical Ascii Control Code Chart Char Dec Hex128 160 192 224 129 161 Available Fonts and Bar Codes Font Valid Ascii CharactersFont Height Width Spacing Page Page Bar Code Summary Data Bar Valid Ascii Characters Code TypeBar Code F EAN-13 Bar Code K Plessey Bar Code p Postnet Bar Code O CodeBar Code S UCC/EAN Code 128 Random Weight Print Resolutions and Maximum Widths Module AssignmentsSpeed Settings and Defaults J693 Function Speed Range Default SettingPrint FeedMenu System Multi-Language Support Required Software CommentNext J693 Menu Language Error Message Description OAdvance File Handling InformationPage J693 Page Page Page Page J693