Pitney Bowes J693 manual System Settings

Page 34

4.1.4 System Settings

INTERNALó MODULE 1024 KB

Sets the number of 1K blocks allocated for the internal RAM ‘D’ module. Available memory dependent upon model; see Appendix C.

DEFAULT MODULE

Sets the default module used to store files

D

when no module is specified; see Appendix C.

 

 

 

SCALEABLE FONT

Sets the number of 1K blocks allocated for

CACHEó

the scaleable font engine. Available memory

0312 KB

dependent upon model; see Appendix C.

 

 

 

SYMBOL SET

Selects the code page used to print single

 

 

byte fonts unless otherwise specified in DPL,

ó

see the Programmer’s Manual.

 

PC_850

61 selectable sets, see the Programmer’s

 

MULTILINGUAL

Manual.

 

 

TIME AND DATE

Allows the user to set Time and Date.

 

 

MEDIA COUNTERS

Internal record of inches printed and time in

 

 

use.

 

ABSOLUTE COUNTER

Shows the number of inches printed and

 

 

number of hours the printer has been

 

 

powered ‘On’ since being set at the factory.

 

 

Not resettable by the user.

 

RESETTABLE

The number of operational hours and inches

 

COUNTER

printed from the date last reset. User may

 

 

reset.

 

RESET COUNTER

Resets the resettable counters to zero.

 

 

PRINT CONFIGURATION

Prints the effective configuration of the

 

 

system. In addition, if settings were changed

 

 

that require a reset to become effective, this

 

 

will be indicated with the ‘§’ symbol.

 

 

A ‘ ’ symbol next to the printed item

 

 

indicates that it was changed via the host but

 

 

not saved in non-volatile memory.

(Continued next page)

24

J693

Image 34
Contents J693 Page Copyright Information Firmware Software AgreementAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Setting Up the PrinterUsing the Front Panel Getting StartedTroubleshooting Adjusting and Maintaining the PrinterSpecifications Appendix C Appendix aAppendix B Appendix DPage About this Printer Standard Features PrintingInspection J693 Installing the Printer Communications Interfacing Serial PortLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon Removal Ribbon routing pathJ693 Ready Mode Normal Operation Ready Light ‘On’ Operating the Front PanelMenu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels LCD Display Indicator LightsLiquid Crystal Display Resetting the Printer Level 1 ResetNavigating the Menu System Keep Host CHANGES? Enter PasswordEnter = YES Sensor Type Media SettingsMedia Type Label LengthPrint Control Present Sensor ModulesCutter Gpio Gpio PortEND of Print System Settings Printer KEY Configuration LevelUpgrade Printer CodeImaging Mode SET Factory DefaultsFormat Attributes Units of Measure Pause ModeSecurity Allegro EmulationSerial Port B CommunicationsSerial Port a Parallel Port aFeedback Mode Host SettingsTimeout Control CodesTest HEX Dump ModeOptions Testing Sensor ReadingsUser Prompts and Condition Messages Understanding the Display MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Printing from the Quick Test Mode Print Quality LabelConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label Validation Label User Defined LabelMedia Sensor Adjustment Media Type Sensor Type Sensor Eye Mark PositionPage Media Sensor Calibration Positioning CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Notched stock place Die-cut stock removeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Printhead Adjustments Burn Line AdjustmentPage Printhead Replacement Cleaning Schedule Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead In5.5.2 Cleaning the Platen Roller Cleaning Interior and Exterior Surfaces Updating the Application ProgramUpdating from the Ready Mode Updating from the Download Mode Application Update Error Messages Application Update ProblemsDescriptions / Causes / Solutions Updating the Boot Loader Program J693 Troubleshooting Tips If experiencing this problem… Try this solution…If experiencing this problem… Try this solution… If an image is on the used ribbon If no image is on the used ribbonIf experiencing this problem… Fault and Warning Messages Description Possible SolutionsFault Messages Ribbon supply hub If media is moving If media is not movingDescription Action Hex Dump Mode Fonts Printer SpecificationsBar Codes ElectricalEnvironmental Requirements Printing SpecificationsMechanical Ascii Control Code Chart Char Dec Hex128 160 192 224 129 161 Available Fonts and Bar Codes Font Valid Ascii CharactersFont Height Width Spacing Page Page Bar Code Summary Data Bar Valid Ascii Characters Code TypeBar Code F EAN-13 Bar Code K Plessey Bar Code p Postnet Bar Code O CodeBar Code S UCC/EAN Code 128 Random Weight Print Resolutions and Maximum Widths Module AssignmentsPrint Speed Settings and DefaultsJ693 Function Speed Range Default Setting FeedMenu System Multi-Language Support Required Software CommentNext J693 Menu Language Error Message Description OAdvance File Handling InformationPage J693 Page Page Page Page J693