Pitney Bowes J693 manual Indicator Lights, LCD Display, Liquid Crystal Display

Page 26

4.0.4Indicator Lights

n

‘On’ indicates READY Mode.

‘Slow Flashing’ indicates Menu Mode.

‘Fast Flashing’ indicates data is being received and processed.

o

‘On’ indicates a ‘Paused’ state.

p

‘Slow Flashing’ indicates a Warning.

‘Fast Flashing’ indicates a Fault.

See Section 6.1 for a list of the display messages.

4.0.5LCD (Display)

nLiquid Crystal Display

The display provides several types of information:

∙ Following a brief power-up sequence, the READY message.

∙ The time and date, if the printer has received it from one of the following: the host, the front panel setting, or the Time and Date option.

∙A label counter during a batch print job.

∙Any prompt, condition, downloading, warning, or fault message.

∙The Menu System when in the Menu Mode.

16

J693

Image 26

Contents J693 Page Copyright Information Firmware Software AgreementAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Setting Up the PrinterUsing the Front Panel Getting StartedSpecifications Adjusting and Maintaining the PrinterTroubleshooting Appendix C Appendix aAppendix B Appendix DPage About this Printer Standard Features PrintingInspection J693 Installing the Printer Communications Interfacing Serial PortLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon Removal Ribbon routing pathJ693 Ready Mode Normal Operation Ready Light ‘On’ Operating the Front PanelMenu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Liquid Crystal Display Indicator LightsLCD Display Resetting the Printer Level 1 ResetNavigating the Menu System Enter = YES Enter PasswordKeep Host CHANGES? Sensor Type Media SettingsMedia Type Label LengthPrint Control Cutter ModulesPresent Sensor END of Print Gpio PortGpio System Settings Printer KEY Configuration LevelUpgrade Printer CodeFormat Attributes SET Factory DefaultsImaging Mode Units of Measure Pause ModeSecurity Allegro EmulationSerial Port B CommunicationsSerial Port a Parallel Port aFeedback Mode Host SettingsTimeout Control CodesTest HEX Dump ModeOptions Testing Sensor ReadingsDescription Conditions Understanding the Display MessagesUser Prompts and Condition Messages User Prompts and Condition Messages Reset in PROGRESS’ Printing from the Quick Test Mode Print Quality LabelConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label Validation Label User Defined LabelMedia Sensor Adjustment Media Type Sensor Type Sensor Eye Mark PositionPage Standard Calibration Positioning CalibrationMedia Sensor Calibration Step Operator Action Displayed Message Comment Press the key to Reflective media place Die-cut stock removeNotched stock place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Printhead Adjustments Burn Line AdjustmentPage Printhead Replacement Cleaning Schedule Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead In5.5.2 Cleaning the Platen Roller Cleaning Interior and Exterior Surfaces Updating the Application ProgramUpdating from the Ready Mode Updating from the Download Mode Descriptions / Causes / Solutions Application Update ProblemsApplication Update Error Messages Updating the Boot Loader Program J693 Troubleshooting Tips If experiencing this problem… Try this solution…If experiencing this problem… Try this solution… If an image is on the used ribbon If no image is on the used ribbonIf experiencing this problem… Fault and Warning Messages Description Possible SolutionsFault Messages Ribbon supply hub If media is moving If media is not movingDescription Action Hex Dump Mode Fonts Printer SpecificationsBar Codes ElectricalMechanical Printing SpecificationsEnvironmental Requirements Ascii Control Code Chart Char Dec Hex128 160 192 224 129 161 Available Fonts and Bar Codes Font Valid Ascii CharactersFont Height Width Spacing Page Page Bar Code Summary Data Bar Valid Ascii Characters Code TypeBar Code F EAN-13 Bar Code K Plessey Bar Code p Postnet Bar Code O CodeBar Code S UCC/EAN Code 128 Random Weight Print Resolutions and Maximum Widths Module AssignmentsPrint Speed Settings and DefaultsJ693 Function Speed Range Default Setting FeedMenu System Multi-Language Support Required Software CommentNext J693 Menu Language Error Message Description OAdvance File Handling InformationPage J693 Page Page Page Page J693