Pitney Bowes J693 manual Printer Specifications, Bar Codes, Fonts, Electrical

Page 85

7.0Printer Specifications

Bar Codes

(See the Programmer’s Manual for details. See Appendix B for visual samples.)

Code 39, Interleaved 2 of 5, Code 128 (subsets A, B and C), Codabar, LOGMARS, UPC-A, UPC-E, UPC 2 & 5 digit addendums, EAN-8, EAN-13, EAN 2 & 5 digit addendums, UPC Random Weight, Code 93, Plessey, Universal Shipping Container Symbology, Code 128 MOD 43, Postnet, USS/EAN-128 Random Weight, Telepen, UPS MaxiCode (modes 2 & 3), PDF417, Data Matrix and QR Code.

Fonts

9 Bit-Mapped Fonts, rotatable 0, 90, 180, 270 degrees CG Triumvirate™ Scalable Font

CG Triumvirate™ Condensed Bold Scalable Font

Communications

Interfaces:	EIA RS-232/DB-25 Serial, and IEEE 1284
	Compliant Parallel
Serial Data Rates:	2400, 4800, 9600, 19.2K, and 38.4K baud.
Handshaking:	Xon/Xoff; CTS/DTR
Parity:	Even, Odd, or None
Stop Bits:	1 or 2
Data Bits:	7 or 8

Electrical

Input Voltage:	90 – 132 or 180 – 264 VAC @ 47–63 Hz, auto-
	ranging.
Power Consumption:	Typical Operating: 90 Watts / Standby: 10 Watts
Grounding:	Unit must be connected to a properly grounded
	receptacle.

J693

75

Image 85

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedTroubleshooting Adjusting and Maintaining the PrinterSpecifications Appendix B Appendix aAppendix C Appendix DPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels LCD Display Indicator LightsLiquid Crystal Display Level 1 Reset Resetting the PrinterNavigating the Menu System Keep Host CHANGES? Enter PasswordEnter = YES Media Type Media SettingsSensor Type Label LengthPrint Control Present Sensor ModulesCutter Gpio Gpio PortEND of Print System Settings Upgrade Printer Configuration LevelPrinter KEY CodeImaging Mode SET Factory DefaultsFormat Attributes Security Pause ModeUnits of Measure Allegro EmulationSerial Port a CommunicationsSerial Port B Parallel Port aTimeout Host SettingsFeedback Mode Control CodesOptions Testing HEX Dump ModeTest Sensor ReadingsUser Prompts and Condition Messages Understanding the Display MessagesDescription Conditions User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Media Sensor Calibration Positioning CalibrationStandard Calibration Step Operator Action Displayed Message Comment Press the key to Notched stock place Die-cut stock removeReflective media place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Application Update Error Messages Application Update ProblemsDescriptions / Causes / Solutions Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Bar Codes Printer SpecificationsFonts ElectricalEnvironmental Requirements Printing SpecificationsMechanical Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsJ693 Function Speed Range Default Setting Speed Settings and DefaultsPrint FeedRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693