Pitney Bowes J693 manual Press the key to

Page 53

Step	Operator Action		Displayed Message	Comment
6	Press the	key. Use	""	See Section
	the	key to scroll	"#	4.1.1 for
	to ‘Sensor Calibration’.			details.

Press the key to

abort this procedure.

7	Press the			key.			See Section
7	Press the			key.	"#"		See Section
						#"	4.1.1 for
							details.
							details.

8	Press the			key.			Sets the

					"#
	Ensure no label media is in				"]<<<_		parameter for
	the Media Sensor then press						the ‘out of
	the Media Sensor then press						the ‘out of
	any key.						stock’
							condition.
							‘yyy’ is a
							numerical value
							representing the
							current sensor
							reading.

(Continued next page)

J693

43

Image 53

Contents J693 Page Firmware Software Agreement Copyright InformationAgency Compliance and Approvals Important Safety Instructions Page Using the Front Panel Setting Up the PrinterPrinter Overview Getting StartedSpecifications Adjusting and Maintaining the PrinterTroubleshooting Appendix B Appendix aAppendix C Appendix DPage About this Printer Printing Standard FeaturesInspection J693 Installing the Printer Serial Port Communications InterfacingLoading Media Page Label Backing Removal 3Loading Ribbon Ribbon routing path Ribbon RemovalJ693 Operating the Front Panel Ready Mode Normal Operation Ready Light ‘On’Menu Mode Configuration Ready Light ‘Flashing’ Quick Test M de Print Test Labels Liquid Crystal Display Indicator LightsLCD Display Level 1 Reset Resetting the PrinterNavigating the Menu System Enter = YES Enter PasswordKeep Host CHANGES? Media Type Media SettingsSensor Type Label LengthPrint Control Cutter ModulesPresent Sensor END of Print Gpio PortGpio System Settings Upgrade Printer Configuration LevelPrinter KEY CodeFormat Attributes SET Factory DefaultsImaging Mode Security Pause ModeUnits of Measure Allegro EmulationSerial Port a CommunicationsSerial Port B Parallel Port aTimeout Host SettingsFeedback Mode Control CodesOptions Testing HEX Dump ModeTest Sensor ReadingsDescription Conditions Understanding the Display MessagesUser Prompts and Condition Messages User Prompts and Condition Messages Reset in PROGRESS’ Print Quality Label Printing from the Quick Test ModeConfiguration Label Quick Ribbon Test Label Dot Test Pattern Label User Defined Label Validation LabelMedia Type Sensor Type Sensor Eye Mark Position Media Sensor AdjustmentPage Standard Calibration Positioning CalibrationMedia Sensor Calibration Step Operator Action Displayed Message Comment Press the key to Reflective media place Die-cut stock removeNotched stock place Key to back out Displayed Message Action Comment Advanced Entry Calibration Hqlrvi Jqqhqlrvi Using the Gain Number Using Key Jrxyjtsjqrr Burn Line Adjustment Printhead AdjustmentsPage Printhead Replacement Recommended Cleaning Schedule Area Method Interval Cleaning ScheduleCleaning the Printhead In5.5.2 Cleaning the Platen Roller Updating the Application Program Cleaning Interior and Exterior SurfacesUpdating from the Ready Mode Updating from the Download Mode Descriptions / Causes / Solutions Application Update ProblemsApplication Update Error Messages Updating the Boot Loader Program J693 If experiencing this problem… Try this solution… Troubleshooting TipsIf experiencing this problem… Try this solution… If no image is on the used ribbon If an image is on the used ribbonIf experiencing this problem… Description Possible Solutions Fault and Warning MessagesFault Messages Ribbon supply hub If media is not moving If media is movingDescription Action Hex Dump Mode Bar Codes Printer SpecificationsFonts ElectricalMechanical Printing SpecificationsEnvironmental Requirements Char Dec Hex Ascii Control Code Chart128 160 192 224 129 161 Font Valid Ascii Characters Available Fonts and Bar CodesFont Height Width Spacing Page Page Bar Valid Ascii Characters Code Type Bar Code Summary DataBar Code F EAN-13 Bar Code p Postnet Bar Code O Code Bar Code K PlesseyBar Code S UCC/EAN Code 128 Random Weight Module Assignments Print Resolutions and Maximum WidthsJ693 Function Speed Range Default Setting Speed Settings and DefaultsPrint FeedRequired Software Comment Menu System Multi-Language SupportNext J693 OAdvance File Handling Information Menu Language Error Message DescriptionPage J693 Page Page Page Page J693