Datamax ST-3210, SV-3306, ST-3306, SV-3210 manual Optional Features

Page 13

1.0.2Optional Features

This printer offers these optional features.

Cutter and Tray (ST Models only):

ØA factory-installed device that will cut stock with a maximum thickness of .008 inch (.2 mm) and a minimum thickness of .0025 inch (.06 mm). The tray attaches to the front of the printer to collect cut tickets, and is capable of stacking a minimum of 100, 3.5-inch (88.9 mm) wide tickets, ranging in lengths from 2.0 inches (50.8 mm) to 5.63 inches (142.9 mm).

Flash Memory Modules:

ØRemovable, permanent storage devices for use with graphics, fonts, and ticket formats, available in different sizes. Order according to module size needed:

	Part Number
Memory Module Size	ST Printer	SV Printer*
256 Kbytes	78-2166-01	DPO78-2443-01
512 Kbytes	78-2166-02	DPO78-2443-02
1 Mbytes	78-2166-03	DPO78-2443-03
2 Mbytes	78-2166-04	DPO78-2443-04

*A Qualified Installer is required for the installation of this option.

Roll Hanger (ST Models only):

ØAn interior mounting option allowing the printer to use 7-inch outer diameter (177.8 mm) rolled stock wound on 2-inch (50.8 mm) diameter cores. Order part number 12-2978-01.

External Keyboard Support:

ØConnection for the DMX Passport™ external keyboard system. Order part number 61-2159-xx

LAN Interface:

ØAn interface that connects the printer to most LAN networks. Order part number 78-2278-01.

ST/SV-3210 and ST/SV-3306

3

Image 13

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Unpacking the Printer Getting StartedAdditional Requirements InspectionAC Selection Switch Required Fuse Rating AC Voltage ConfigurationInterfacing the Printer Printer power and interface connections ST Models Loading Ticket StockPage SV Models Installing a Memory Module ST Models SV Models Using the Front PanelTicket Exit Two functions Three functionsResident Formats Configuration TicketTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset TOF Sensor Adjustment Adjusting Maintaining the PrinterST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Database Modification Example Printer will turn off the On-Line Indicator and printRecommended Cleaning Schedule Area Method Interval MaintenanceST Models Raise Cleaning the PrintheadCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Exterior Surface Cleaning Interior CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Manufacturer Material Comment Approved Ticket StocksST/SV-3210 and ST/SV-3306 Appendix a Ascii Control Code ChartAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Font Number Font ID Font Size Box Size Dtpl FontsDtpl Font Samples Font Barcode Type Length Checksum Valid Characters DPL BarcodesDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Cable Listings Appendix CST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Thermal Printhead, Belts, and Platen Roller PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69