Datamax SV-3306, ST-3210, ST-3306, SV-3210 manual Database Modification Example

Page 40

4.3.1Database Modification Example

This section details the modification of an Operational Database parameter. The following example increases the printing speed parameter from 6 to 8 IPS on the ST-3210; however, using the same basic procedure, any of the parameters can be changed regardless of the printer model.

ŒIf on-line, press the PAUSE button to place the printer off-line.

•Press and hold the F2 button until the On-Line Indicator is lit (approximately six seconds) then release.

The printer will turn off the On-Line Indicator and print:

STOCK ID

=

5

ŽPress the F2 button three times (allow time for printing following each button press), to arrive at the Print Speed parameter.

The printer will print:	PRINT SPEED	=	6	IPS
	PARSER MODE	=	DTPL
	TICKET WIDTH =		189	(48	MM)
	STOCK ID	=	5

•Press the F1 button two times (again, allow time for printing following each button press), to arrive at the 8 IPS setting.

The printer will print:	PRINT SPEED	=	8	IPS
	PRINT SPEED	=	7	IPS
	PRINT SPEED	=	6	IPS
	PARSER MODE	=	DTPL
	TICKET WIDTH =		189	(48	MM)
	STOCK ID	=	5

•To save the changes and exit the mode, press and hold the F2 button until the On-Line Indicator is lit (approximately six seconds) then release.

The parameter changes can be confirmed by printing a Configuration Ticket; see Section 3.5.1.

30	ST/SV-3210 and ST/SV-3306

Image 40

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69