Datamax ST-3210, SV-3306, ST-3306, SV-3210 manual Specifications

Page 53

Specifications

6.0Specifications

Communications

Character Set:

ANSI ASCII

Parallel Interface Port:

Centronicsâ type 36-pin

Serial Interface Port:

RS-232c and RS-422; DB25

Baud Rates:

600, 1200, 2400, 4800, 9600, 19.2K and 38.4K

Word Length and Parity:

Selectable data format:

 

7-bit word with even parity, or

 

8-bit word with no parity

Handshaking:

Xon/Xoff and CTS & DTR.

Input Buffer:

Serial: Approximately 6 Kbytes. XOFF is

 

transmitted and DTR goes low with 750 bytes

 

available in the buffer. XON is transmitted and

 

DTR goes high when 1000 bytes remain in the

 

buffer. Characters are transmitted without

 

parity from the printer.

 

Parallel: 1KBytes.

Control (Front) Panel

Indicators:

Power, Fault and On-Line.

Buttons:

Dual Purpose: Pause/F1; Feed/F2; and Test/F3

Potentiometer:

0-20 darkness settings

Electrical

Input Voltage, Configurable:

Circuit Protection:

Grounding:

105 − 125 VAC, or

210 − 250 VAC; 47-63 Hz.

115 VAC: 1.6A Time Delay Fuse.

230 VAC: 0.8A Time Delay Fuse.

Unit must be connected to a properly grounded receptacle.

ST/SV-3210 and ST/SV-3306

43

Image 53
Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page ST Table Model Printer OverviewAbout the Printer Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Unpacking the Printer Getting StartedAdditional Requirements InspectionAC Selection Switch Required Fuse Rating AC Voltage ConfigurationInterfacing the Printer Printer power and interface connections ST Models Loading Ticket StockPage SV Models Installing a Memory Module ST Models SV Models Using the Front PanelTicket Exit Two functions Three functionsResident Formats Configuration TicketTest Pattern Ticket Internal Test Ticket Factory Default Reset Resetting the PrinterWarm Reset TOF Sensor Adjustment Adjusting Maintaining the PrinterST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Database Modification Example Printer will turn off the On-Line Indicator and printRecommended Cleaning Schedule Area Method Interval MaintenanceST Models Raise Cleaning the PrintheadCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Exterior Surface Cleaning Interior CleaningTry this solution… TroubleshootingTroubleshooting Tips Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Manufacturer Material Comment Approved Ticket StocksST/SV-3210 and ST/SV-3306 Appendix a Ascii Control Code ChartAscii Control Code Chart DPL Fonts Appendix BAvailable Fonts and Barcodes DPL Font Samples ST/SV-3210 and ST/SV-3306 Font Number Font ID Font Size Box Size Dtpl FontsDtpl Font Samples Font Barcode Type Length Checksum Valid Characters DPL BarcodesDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Cable Listings Appendix CST/SV-3210 and ST/SV-3306 Appendix D SV Model Mounting DimensionsTop Plate Dimensions Side Dimensions Thermal Printhead, Belts, and Platen Roller PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69