Datamax SV-3210, SV-3306, ST-3210, ST-3306 manual Cleaning the Platen Roller

Page 43

4.4.2Cleaning the Platen Roller

Print quality can decline if the platen roller becomes contaminated with paper dust, grit or adhesive. When this build-up is not removed, it can cause abrasive damage to the printhead. To clean the Platen Roller:

ŒTurn ‘Off’ and unplug the printer.

•ST Models: Raise the access cover; see Section 3.2.

ŽSlide the printhead latch to the unlocked position, raise the Printhead Assembly (see Section 4.4.1) and remove the ticket stock.

•Using a cotton swab or lint-free cloth moistened with isopropyl alcohol, remove all debris from the Platen Roller. Manually rotate the roller and repeat to clean the entire surface.

•Allow the Platen Roller to dry, then lower the Printhead Assembly and slide the printhead latch into the locked position.

‘ Plug in and turn ‘On’ the printer.

’ Load ticket stock; see Section 3.2.

“ ST Models: Close the

access cover.

þNote: NEVER use a sharp object to clean the Platen Roller.

ST/SV-3210 and ST/SV-3306

33

Image 43

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Unpacking the Printer Getting StartedAdditional Requirements InspectionAC Selection Switch Required Fuse Rating AC Voltage ConfigurationInterfacing the Printer Printer power and interface connections ST Models Loading Ticket StockPage SV Models Installing a Memory Module ST Models SV Models Using the Front PanelTicket Exit Two functions Three functionsResident Formats Configuration TicketTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset TOF Sensor Adjustment Adjusting Maintaining the PrinterST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Database Modification Example Printer will turn off the On-Line Indicator and printRecommended Cleaning Schedule Area Method Interval MaintenanceST Models Raise Cleaning the PrintheadCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Exterior Surface Cleaning Interior CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Manufacturer Material Comment Approved Ticket StocksST/SV-3210 and ST/SV-3306 Appendix a Ascii Control Code ChartAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Font Number Font ID Font Size Box Size Dtpl FontsDtpl Font Samples Font Barcode Type Length Checksum Valid Characters DPL BarcodesDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Cable Listings Appendix CST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Thermal Printhead, Belts, and Platen Roller PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69