Datamax ST-3306, SV-3306, ST-3210, SV-3210 manual Interior Cleaning, Exterior Surface Cleaning

Page 46

4.4.5Interior Cleaning

ST Models only: Ticket Compartment Cleaning

During normal operation, paper particles from the ticket stock accumulate inside the printer. These particles can stick to the ticket and cause voids in the print, reducing print quality. To clean the interior of the printer:

Œ Turn ‘Off’ and unplug the printer.

• Raise the access cover; see Section 3.2.

Ž Slide the printhead latch to the unlocked position,

raise the Printhead Assembly (see Section 4.4.1) and remove the ticket stock.

•Using a soft brush or compressed air, remove all debris accumulated inside the ticket compartment.

•Plug in and turn ‘On’ the printer.

‘Load ticket stock (see Section 3.2).

’Close the access cover.

4.4.6Exterior Surface Cleaning

The exterior surface can be cleaned using a general purpose cleaner and a soft cloth or sponge. Never use abrasive cleansers or solvents. To clean:

ŒTurn ‘Off’ and unplug the printer.

•Gently wipe the exterior surfaces until clean and then allow time to dry.

ŽPlug in and turn ‘On’ the printer.

36	ST/SV-3210 and ST/SV-3306

Image 46

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69