Datamax ST-3210, SV-3306, ST-3306, SV-3210 manual

Page 21

To use roll ticket stock, the stock must be mounted on the optional Roll Hanger, as shown. (See Section 6 for stock requirements.)

þ Note: To use an internal fanfold ticket source on a printer equipped with the Roll Hanger option, first remove the Roll Hanger by unscrewing it from the printer. Store the hanger in a safe place for future use.

•Loosen the Thumbscrew and adjust the Media Guides to fit the width of the ticket stock: the guides should be positioned close enough to stop side-to-side ticket movement, but not so tight to cause friction or bowing of the ticket stock (see below). Tighten the Thumbscrew to secure the guides in place.

‘Slide the ticket stock through the Media Guides. The motor will start; continue sliding the tickets. The printer will grab the leading edge of the stock and complete the positioning process. Close the Access Cover.

þNotes: If automatic loading doesn’t occur:

1)Ensure that the Printhead Latch is locked.

2)Press the PAUSE button (the On-Line Indicator should be ‘Off’ now).

3)Repeatedly press the F2 button while gently pushing the stock forward until the printer grabs the ticket.

4)Press the PAUSE button (to return to the on-line mode).

If the ticket was not fed to a proper position, the TOF Sensor may need adjustment; see Section 4 for details.

ST/SV-3210 and ST/SV-3306

11

Image 21

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page Printer Overview About the PrinterST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Unpacking the Printer Getting StartedAdditional Requirements InspectionAC Selection Switch Required Fuse Rating AC Voltage ConfigurationInterfacing the Printer Printer power and interface connections ST Models Loading Ticket StockPage SV Models Installing a Memory Module ST Models SV Models Using the Front PanelTicket Exit Two functions Three functionsResident Formats Configuration TicketTest Pattern Ticket Internal Test Ticket Resetting the Printer Warm ResetFactory Default Reset TOF Sensor Adjustment Adjusting Maintaining the PrinterST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Database Modification Example Printer will turn off the On-Line Indicator and printRecommended Cleaning Schedule Area Method Interval MaintenanceST Models Raise Cleaning the PrintheadCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Exterior Surface Cleaning Interior CleaningTroubleshooting Troubleshooting TipsTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Manufacturer Material Comment Approved Ticket StocksST/SV-3210 and ST/SV-3306 Appendix a Ascii Control Code ChartAscii Control Code Chart Appendix B Available Fonts and BarcodesDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Font Number Font ID Font Size Box Size Dtpl FontsDtpl Font Samples Font Barcode Type Length Checksum Valid Characters DPL BarcodesDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Cable Listings Appendix CST/SV-3210 and ST/SV-3306 SV Model Mounting Dimensions Top Plate DimensionsAppendix D Side Dimensions Thermal Printhead, Belts, and Platen Roller PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69