Datamax ST-3306, SV-3306, ST-3210, SV-3210 manual SV Models

Page 22

3.2.2SV Models

ŒPlug in and turn ‘On’ the printer.

•Place fanfold ticket stock in the bottom of the enclosure, bring the stock up to the Media Guides. (The TOF Mark should be facing away from the Printhead Latch; see Section 4.) Ensure that the Printhead Latch is locked.

ŽLoosen the Thumbscrew and adjust the Media Guides to fit the width of the ticket stock as described in Step 5 of Section 3.2.1.

•Slide the ticket stock through the Media Guides. The motor will start; continue feeding the tickets. The printer will grab the leading edge of the stock and complete the positioning process. If this process fails, see the note below.

þNotes: If automatic loading fails to occur, see the note at the end of Section 3.2.1.

If the ticket did not feed to a proper position, the TOF Sensor may need adjustment; see Section 4 for details.

12	ST/SV-3210 and ST/SV-3306

Image 22

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69