Datamax ST-3306, SV-3306, ST-3210, SV-3210 manual Stock ID Selections

Page 34

4.1Stock ID Selections

The printer maintains a selection of 10 user modifiable stock setups. Each setup defaults to a specific print width, start print position and cut/tear position, where:

Ø The Print Width is the print distance across the ticket.

Ø The Start of Print Position is the distance, measured in inches, from the TOF Sensor to printhead burnline.

ØThe Cut/Tear Position is the distance, measured in inches, from the TOF

Sensor to the cut (if equipped) or tear position of the printed ticket.

The Stock ID can be set using the Operational Database Modification procedure (see Section 4.3.1). As defined on the following page, Stock ID numbers 0 through 8 are not changeable through host commands; however, Stock ID 9 will allow host commands to override the default settings.

If none of the listed Stock ID selections fit your media, select the Stock ID that is closest to the physical dimensions of your stock and then modify the Start of Print and Cut/Tear positions (see Section 4.2). All changes can be saved to the Stock ID, allowing commonly used formats to be recalled. To revert to the default values, reset the printer (see Section 3.6).

24	ST/SV-3210 and ST/SV-3306

Image 34

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page About the Printer Printer OverviewST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Warm Reset Resetting the PrinterFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Tips TroubleshootingTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Available Fonts and Barcodes Appendix BDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 Top Plate Dimensions SV Model Mounting DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69