Datamax ST-3210, SV-3306 manual AC Voltage Configuration, AC Selection Switch Required Fuse Rating

Page 17

Setting up the Printer

This section details the connections, loading methods, memory module installation, and resident ticket formats of the printer.

3.0AC Voltage Configuration

Depending upon the configuration of the AC Selection Switch and fuse, the printer is capable of either 115 or 230 VAC single-phase operation.

Before connecting power, check the voltage configuration: (1) locate the AC Selection Switch and Fuse Holder (containing the fuse) on the Back Panel, then (2) referencing the table below, ensure that the AC Selection Switch setting and fuse rating correspond to your AC Source Voltage.

Failure to verify the AC Selection Switch setting and fuse rating can result in personal injury and/or printer damage.

CAUTION

AC Source Voltage	AC Selection Switch	Required Fuse Rating
105 – 125 VAC	115 VAC	1.6 amp / 250V slow-blow
210 – 250 VAC	230 VAC	0.8 amp / 250V slow-blow

ST/SV-3210 and ST/SV-3306

7

Image 17

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page ST Table Model Printer OverviewAbout the Printer Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Unpacking the Printer Getting StartedAdditional Requirements InspectionAC Selection Switch Required Fuse Rating AC Voltage ConfigurationInterfacing the Printer Printer power and interface connections ST Models Loading Ticket StockPage SV Models Installing a Memory Module ST Models SV Models Using the Front PanelTicket Exit Two functions Three functionsResident Formats Configuration TicketTest Pattern Ticket Internal Test Ticket Factory Default Reset Resetting the PrinterWarm Reset TOF Sensor Adjustment Adjusting Maintaining the PrinterST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Database Modification Example Printer will turn off the On-Line Indicator and printRecommended Cleaning Schedule Area Method Interval MaintenanceST Models Raise Cleaning the PrintheadCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Exterior Surface Cleaning Interior CleaningTry this solution… TroubleshootingTroubleshooting Tips Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Manufacturer Material Comment Approved Ticket StocksST/SV-3210 and ST/SV-3306 Appendix a Ascii Control Code ChartAscii Control Code Chart DPL Fonts Appendix BAvailable Fonts and Barcodes DPL Font Samples ST/SV-3210 and ST/SV-3306 Font Number Font ID Font Size Box Size Dtpl FontsDtpl Font Samples Font Barcode Type Length Checksum Valid Characters DPL BarcodesDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Cable Listings Appendix CST/SV-3210 and ST/SV-3306 Appendix D SV Model Mounting DimensionsTop Plate Dimensions Side Dimensions Thermal Printhead, Belts, and Platen Roller PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69