Datamax ST-3306, SV-3306, ST-3210, SV-3210 manual Interfacing the Printer

Page 18

3.1Interfacing the Printer

Interfacing the printer to the host computer can be made through either a parallel or a serial cable (see Appendix C for cable requirements). Communication port selection is automatic: the first port to receive data is set ‘active’ by the printer. To change an active port, cycle the power ‘Off’ and ‘On’ or perform a Warm Reset (see Section 3.6.1).

Parallel Interface Port:

The parallel interface supports Centronicsâ parallel communications.

Serial Interface Port:

The serial interface supports either RS-232 or RS-422 communications. The following menu-selectable serial port settings must be configured to match those of the host computer; see Section 4.3.

∙Baud Rate

∙Word Length (including Parity, which defaults to either of the following):

8-bit word with no parity

7-bit word with even parity

þ Note: If unable to establish communications, see Section 5 for help.

8	ST/SV-3210 and ST/SV-3306

Image 18

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page Printer Overview About the PrinterST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Resetting the Printer Warm ResetFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Troubleshooting TipsTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Appendix B Available Fonts and BarcodesDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 SV Model Mounting Dimensions Top Plate DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69