Datamax SV-3306, ST-3210, ST-3306, SV-3210 manual Start of Print & Cut/Tear Adjustment

Page 36

4.2Start of Print & Cut/Tear Adjustment

If none of the preset Stock ID parameters meet the needs of your application, then the Start of Print (SOP) and Cut/Tear (C/T) Adjustments can be used to visually set the required positions. To begin:

Œ If on-line, press the PAUSE button to place the printer off-line.

Press and hold (approximately 6 seconds) the F3 button until the On- Line Indicator is lit then release. The SOP setup is first, to adjust:

ØPress the F1 button to increase the current distance (pressing and holding will rapidly move the ticket).

ØPress the F2 button to decrease the current distance (pressing and holding will rapidly move the ticket).

ØPress the F3 button to print a ticket showing the new setting.

ŽAfter completing the SOP adjustment, press and hold (approximately 6 seconds) the F3 button until the On-Line Indicator is lit then release.

Next, adjust the Cut/Tear position using the F1, F2 and F3 buttons as described above.

After completing the Cut/Tear adjustment, return the printer to

the off-line mode by pressing and

holding the F3 button until the On-Line Indicator is lit then release.

Press the PAUSE button to return to the on-line mode.

þNotes: This procedure must be performed in its entirety, even when no change is desired for one of the settings.

After completing the adjustments, always confirm the new settings by printing several test tickets.

If cutting, the cut position on the ticket should occur just behind the perforation, never in front of the perforation.

26

ST/SV-3210 and ST/SV-3306

Image 36
Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page Printer Overview About the PrinterST Table Model Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Resetting the Printer Warm ResetFactory Default Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTroubleshooting Troubleshooting TipsTry this solution… Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart Appendix B Available Fonts and BarcodesDPL Fonts DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 SV Model Mounting Dimensions Top Plate DimensionsAppendix D Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69