Datamax SV-3306, ST-3210, ST-3306, SV-3210 manual Ticket Stock Requirements

Page 56

Print Engine (continued)

Maximum Fields and	600 fields with 16,000 characters per ticket
Characters Per Ticket:
Tear Bar:	Tear up/down
DRAM Memory:	4 MB
Internal Module Size:	512 KB (default)
Scalable Module Size:	256 KB (default)
EPROM Memory:	1 MB

Ticket Stock Requirements

Type:	Fan-fold and roll (if option equipped)
	reflective[1] direct thermal stock.
Maximum Ticket Width:	3.25 inches (82.55 mm)
Minimum Ticket Width:	1.9 inches (48.2 mm)
Ticket Thickness Range:	.005 inch – .010 inch (.13 mm – .25 mm)
(if Cutter option equipped):	.025 inch – .008 inch (.06 mm – .2 mm)
Fanfold Ticket Length	11.375 inches (289 mm) maximum for interior
(ST models only):	placement of the stock.
Fanfold Ticket Height	4.5 inches (114.3 mm) maximum for interior
(ST models only):	placement of the stock.
Roll Capacity	7.0-inch (177.8 mm) maximum outer diameter
(if Roll Hanger option	rolls of ticket stock wound with the TOF Marks
equipped):	facing inward, on 2.0-inch (50.8 mm) diameter
	cores.

[1]The reflective TOF Mark must be black, carbon based, and placed on the backside of the stock with a minimum size of .125 inch (3.175 mm) long (direction of travel) by

.5 inch (12.7 mm) wide, with the center falling between .235 inch (6 mm) and 3.03 inches (77 mm) from the edge while allowing adequate Quiet Zone space (see the diagram in Section 6.1). The reflectance of the mark shall be less than 10% at wavelengths of 950 and 640 nm.

46	ST/SV-3210 and ST/SV-3306

Image 56

Contents ST/SV 3210 & ST/SV Operator’s Manual Page Copyright Information Page Agency Compliance and Approvals Important Safety Instructions Contents Troubleshooting Warranty Information Glossary Index Page ST Table Model Printer OverviewAbout the Printer Standard Features Optional Features ST/SV-3210 and ST/SV-3306 Getting Started Unpacking the PrinterInspection Additional RequirementsAC Voltage Configuration AC Selection Switch Required Fuse RatingInterfacing the Printer Printer power and interface connections Loading Ticket Stock ST ModelsPage SV Models Installing a Memory Module Using the Front Panel ST Models SV ModelsTicket Exit Three functions Two functionsConfiguration Ticket Resident FormatsTest Pattern Ticket Internal Test Ticket Factory Default Reset Resetting the PrinterWarm Reset Adjusting Maintaining the Printer TOF Sensor AdjustmentST Model TOF Sensor Adjustment SV Model TOF Sensor Adjustment Stock ID Selections Position Start of Print & Cut/Tear Adjustment Operational Database Modification Auto Bit word Parit Printer will turn off the On-Line Indicator and print Database Modification ExampleMaintenance Recommended Cleaning Schedule Area Method IntervalCleaning the Printhead ST Models RaiseCleaning the Platen Roller TOF Sensor Cleaning Ticket Detect Sensor Cleaning Interior Cleaning Exterior Surface CleaningTry this solution… TroubleshootingTroubleshooting Tips Reconfigure to match, see Section Not meet specifications see Section Try this solution… Hex Dump Mode ST/SV-3210 and ST/SV-3306 Specifications SpecificationsEnvironmental Mechanical Ticket Stock Requirements Approved Ticket Stocks Manufacturer Material CommentST/SV-3210 and ST/SV-3306 Ascii Control Code Chart Appendix aAscii Control Code Chart DPL Fonts Appendix BAvailable Fonts and Barcodes DPL Font Samples ST/SV-3210 and ST/SV-3306 Dtpl Fonts Font Number Font ID Font Size Box SizeDtpl Font Samples DPL Barcodes Font Barcode Type Length Checksum Valid CharactersDPL Bar Code Samples Bar Code I Codabar Bar Code K Plessey Barcode T Telepen Dtpl Barcodes Appendix C Cable ListingsST/SV-3210 and ST/SV-3306 Appendix D SV Model Mounting DimensionsTop Plate Dimensions Side Dimensions Printer Thermal Printhead, Belts, and Platen RollerWarranty Service Procedures General Warranty ProvisionsLimitation of Liability ST/SV-3210 and ST/SV-3306 Glossary ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 ST/SV-3210 and ST/SV-3306 Index Ticket stock, 10 12, 21 23, 28, 29 38, 39, 46, 47, 69