Citizen Systems Model CMP-10 manual Esc +, ESC n, Hex Type

Page 19

ESC +

[Function]	Switch OFF the printer
[Code]	<1B>H<2B>H
[Range]	None
[Outline]	This command is used for switching off the printer from the host.
	Sending this command causes the same operation as that by setting the power switch
	to off.

ESC – n

[Function]	Specifying/ Canceling Underline
[Code]	<1B>H<2D>H<n>
[Range]	{0 =< n =< 02(Hex)}
[Outline]	Specifying/canceling an underline.
	¥		Types of underlines by n value are shown below:

			n (Hex)	Type
			0	Canceling an underline.

			1	Specifying an underline for 1-dot width.
			2	Specifying an underline for 2-dots width.
[Caution]	¥		An underline is attached to the full character width. It is, however, not attached to
			the part having been skipped by horizontal tab command.
	¥		An underline is not attached to a 90¡- right-turned characters.
[Default]	n = 0
[See Also]	ESC !
[Sample Program]

PRINT #1, CHR$ (&H1B) + “–” + CHR$ (0);

PRINT #1, “AAAAA” ;

PRINT #1, CHR$ (&H1B) + “–” + CHR$ (1);

PRINT #1, “AAAAA” + CHR$ (&HA);

[Print Results]

Underline Canceled

>

>

A A A A A A A A A A

>

>

Underline Specified

Ñ 17 Ñ

Image 19

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU