Citizen Systems Model CMP-10 manual Esc @, Sample Program

Page 25

ESC @

[Function]	Initializing the Printer
[Code]	<1B>H<40>H
[Outline]	Clears data stored in the print buffer and brings various settings to the initial state
	(Default state). Items not cleared are as shown below.
	¥ Data inside the internal input buffer are not cleared.
	¥ Does not clear any data in the internal input buffer.
	¥ Does not clear downloaded characters.
	¥ Does not clear defined downloaded characters.
	¥ Does not clear defined downloaded bit image.
	¥ Does not clear defined macro.
	¥ Does not clear setting for print density.
	¥ Does not clear baud rate setting of serial port.
	¥ Does not clear valid/invalid setting for panel switch.
	¥ Does not clear ASB mode setting.
	¥ Does not clear setting for auto power-off time.
	¥ Does not clear memory switch.
[Caution]	At power off, the following settings are cleared in addition to the items cleared by
	this command.
	¥ Clears input buffer.
	¥ Clears macro.
	¥ Return ASB mode according to the memory switch setting.
	¥ Clears valid/invalid setting for panel switch.
[Sample Program]
	PRINT #1, CHR$ (&H1B) + “ ! “ + CHR$ (&H30) ;
	PRINT #1, CHR$ (&H1B) + “V” + CHR$ (1);
	PRINT #1, “AAA” + CHR$ (&HA);
	PRINT #1, CHR$ (&H1B) + “@”;
	PRINT #1, “AAA” + CHR$ (&HA);
[Print Results]	A A A
	A A A
	A A A

Ñ 23 Ñ

Image 25

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set ESC T ESC S nHex Speed bps Model CMP-10 VerHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnJAN-8 CODE93 CODE128GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU