Citizen Systems Model CMP-10 manual Esc Rs, Default

Page 9

CR

[Function]

Print one line Command

[Code ]

<0D>H

[Outline]

This command is ignored or its action is the same as LF depending on the last

 

execution of GS ) 2 command (FLAG SETTING COMMAND).

 

If Flag 2 is 0, carriage return (CR) command is ignored.

 

If Flag 2 is 1, CR comamnd will act as LF command.

[Default]

CR command is ignored. If you want that it acts like LF command set flag 2 to 1 by

 

GS ) command.

[See Also]

GS )

ESC RS

[Function]

Sounds the Buzzer

[Code]

<1B>H<1E>H

[Outline]

By executing this command the buzzer will beep.

 

This command functions in the same manner as BEL.

Ñ 7 Ñ

Image 9
Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H GS LGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC J n ESC R nHex Character Set ESC T ESC S nHex Speed bps Model CMP-10 VerHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnJAN-8 CODE93 CODE128GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU