Citizen Systems Model CMP-10 manual GS n m, Memory Switch OFF

Page 44

GS ) n m

[Function]

Setting of printer flags

 

 

[Code]

<1D>H<29>H<n><m>

 

 

[Range]

{0 =< n =< 8(Hex)}

 

 

 

{m = 0 or 1(Hex)}

 

 

[Outline]

This model has 8 memory switches and selecting, releasing, and changing a function

 

is available with this command.

 

 

Memory switch setting is retained even after printer power off.

 

n specifies the number of memory switch to be operated.

 

m specifies a selection.

 

 

 

The contents of individual memory switches are as shown below.

 

 

 

 

 

Memory Switch

OFF (0)

ON (1)

 

1

Slach 0

Normal 0

 

2

CR is ignored

CR has the same action as LF

 

 

 

 

 

3

Default font A

Default font B

 

 

 

 

 

4

Prints ÒLow BatteryÓ.

Does not print ÒLow BatteryÓ.

 

5

ASB Invalid for default

ASB Valid for default

 

6

Not in use

 

 

 

 

 

 

7

IrDA protocol enabled

IrDA protocol disabled

 

8

Shift JIS for default

JIS for default

[Caution]

The setting of the changed memory switch is enabled by resetting the power switch.

No. 8 is only for Japanese model.

Ñ 42 Ñ

Image 44
Contents Command Reference Revision CMP-10 Command SET Code Command FunctionGS W GS HGS L Command Details Xxxx ALLBEL Sample Program Print Results0AH ESC RS Default Sample Program ESC SP nBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n Initialize command ESC & m n1 n2 d kMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n ESC = n Bit Equipment Value21 Ñ ESC ? n Hex TrackESC @ ESC D n k NUL See Also Sample Program Print ResultsESC E n ESC G n Hex Character Set ESC J nESC R n ESC S n ESC THex Speed bps Model CMP-10 VerESC V n Hex ConditionESC Y n ESC Z ByteUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` ESC a n Hex PositionESC c5 n ESC d n ESC ESC x n B B B Memory Switch OFF GS n mGS * n1 n2 d n1 n2 D1 ...... Dn See Also Sample ProgramGS / m Hex Name Dot Density Vertical Direction Horizontal Direction1DH3AH GS H n Hex Printing PositionGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex Hex Mode GS n1 n2 n3GS a n Bit Status Item Addressed by ABSNot in use Thermal head is overheated Disabled for ASB may also have changed GS f n Hex Font1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Hex Code set a Code set B Code set CType Print Sample Outline of Symbol Max. Column Descriptionof Bar CodesJAN-8 CODE93 CODE128GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Bluetooth Init Commands ExampleBlack Mark Function ESC l nDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 If YES is not chosen, the changed setting will not be lost Change IrDA MAX Speed ?Memory switches OFF0 ON1 Memory switch 8 =Change Print Density ? Programming Considerations Pin No Signal Direction Function Pin No. of Cable Serial InterfaceExplanation of Input/Output Signals 14, 15 pin Communicate mode settingElectrical Characteristics RS-232C CircuitInfrared Communication Specifications IrComm 3 Wire raw IrLPTMechanical Specification McbfPower Related Specifications BatteryUL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard