Citizen Systems Model CMP-10 manual ESC ! n, Bit Function Value, Default See Also

Page 11

ESC ! n

[Function]	Collective Specifying Printing Mode
[Code]	<1B>H<21>H<n>
[Range]	{0 =< n =< FF(Hex)}
[Outline]	Printing mode is assigned.

	Bit	Function	Value
	Bit	Function	0	1
			0	1
	0	Character Font	Font A	Font B
	1	Undefined
	2	Undefined
	3	High-lighting	Canceled	Specified
	4	Double height	Canceled	Specified

	5	Double width	Canceled	Specified
	6	Undefined
	7	Underline	Canceled	Specified
	Each n bit indicates the following:
[Caution]	¥ With double height and double width being specified simultaneously, double wide
	and double high characters are consisted.

¥An underline is attached to the full character width, which, however, is not attached to the part having been skipped by the horizontal tab.

Neither is it attached to 90¡-right-turned characters.

¥The underline width is as having been specified by <ESC ->. (The default setting is 1 dot width.)

¥n case that double wide character and normal character exist in same one line, the layout of underline is consistent one.

[Default]	n = 0
[See Also]	ESC E, ESC Ð

Ñ 9 Ñ

Image 11

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS W GS HGS L Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n Hex Character Set ESC J nESC R n Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsUL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard