Citizen Systems Model CMP-10 manual GS W n

Page 50

GS W n

[Function]	Setting the print area width
[Code]	<1D>H<57>H<nL><nH>
[Range]	{0 =< nL =< FF(Hex)}
	{0 =< nH =< FF(Hex)}
[Outline]	Sets the print area width specified by nL and nH.

¥The print area width will be [(nL + nH ⋅ 256) ⋅ 1/203] inches.

Printable Area

Left Margin

Printable Area With

[Caution]

¥ This command only works when it is entered at the beginning of a line.

¥If the value entered with this command exceeds the printable area for one line, the entire area except the left margin is set as the print area width.

¥For calculation of print area width, the basic pitch 1/203 inch for horizontal direction is used.

(1)The print area is extended toward the right to accommodate the first character, but not wider than the printable area.

Printable Area

A

Extended toward the right

Left Margin

Printable Area Width

(2)When sufficient area cannot be secured even by executing the processing (1), the print area is extended to the left (decreasing left margin).

Printable Area

A
Left Margin	(1) Extended
(2) xxxx	toward the right

Printable Area Width

Ñ 48 Ñ

Image 50

Contents Command Reference Revision CMP-10 Command SET Code Command FunctionGS W GS HGS L Command Details Xxxx ALLBEL Sample Program Print Results0AH ESC RS Default Sample Program ESC SP nBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n Initialize command ESC & m n1 n2 d kMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n ESC = n Bit Equipment Value21 Ñ ESC ? n Hex TrackESC @ ESC D n k NUL See Also Sample Program Print ResultsESC E n ESC G n Hex Character Set ESC J nESC R n Hex Speed bps ESC S nESC T Model CMP-10 VerESC V n Hex ConditionESC Y n ESC Z ByteUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` ESC a n Hex PositionESC c5 n ESC d n ESC ESC x n B B B Memory Switch OFF GS n mGS * n1 n2 d n1 n2 D1 ...... Dn See Also Sample ProgramGS / m Hex Name Dot Density Vertical Direction Horizontal Direction1DH3AH GS H n Hex Printing PositionGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex Hex Mode GS n1 n2 n3GS a n Bit Status Item Addressed by ABSNot in use Thermal head is overheated Disabled for ASB may also have changed GS f n Hex Font1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Hex Code set a Code set B Code set CJAN-8 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes CODE93 CODE128GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Bluetooth Init Commands ExampleBlack Mark Function ESC l nDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 If YES is not chosen, the changed setting will not be lost Change IrDA MAX Speed ?Memory switches OFF0 ON1 Memory switch 8 =Change Print Density ? Programming Considerations Pin No Signal Direction Function Pin No. of Cable Serial InterfaceExplanation of Input/Output Signals 14, 15 pin Communicate mode settingElectrical Characteristics RS-232C CircuitInfrared Communication Specifications IrComm 3 Wire raw IrLPTMechanical Specification McbfPower Related Specifications BatteryUL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard