Citizen Systems manual ESC S n, Esc T, Hex Speed bps, Model CMP-10 Ver

Page 30

ESC S n

[Function]	Setting serial interface communication speed
[Code]	<1B>H<53>H<n>
[Range]	{0 =< n =< 6(Hex)}
	{30 =< n =< 36(Hex)}

	n (Hex)	Speed (bps)
	0, 30	1200
	1, 31	2400

	2, 32	4800

	3, 33	9600
	4, 34	19200
	5, 35	57600

	6, 36	115200
	7, 37	38400 (Firmware 2.04 or later)
[Outline]	Sets the communication speed for the serial interface.
	The command is valid only when the printer is connected through a serial cable. It is
	not valid when using IrDA interface. The last setting is valid even after the printer is
	switched OFF.
[Default]	The default value is 3 [9600 BPS]

ESC T

[Function]	Printing Diagnostic information
[Code]	<1B>H<54>H
[Outline]	Prints current printer attributes and diagnostics.
[See Also]	ESC .
[Print Results]	CITIZEN Mobile Printer
	/////////////////////////////////////////////
	Model CMP-10 Ver x.xxXX
	Intensity:	100%
	Timeout:	10 min
	Temperature:	27°C
	Battery:	7.5V [**...]
	Mode:	RS232
	Speed:	9600 bps
	Switches:	0 0 0 0 0 0 0 0

Ñ 28 Ñ

Image 30

Contents Command Reference Revision CMP-10 Command SET Code Command FunctionGS H GS LGS W Command Details Xxxx ALLBEL Sample Program Print Results0AH ESC RS Default Sample Program ESC SP nDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n Initialize command ESC & m n1 n2 d kHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n ESC = n Bit Equipment Value21 Ñ ESC ? n Hex TrackESC @ ESC D n k NUL See Also Sample Program Print ResultsESC E n ESC G n ESC J n ESC R nHex Character Set Hex Speed bps ESC S nESC T Model CMP-10 VerESC V n Hex ConditionESC Y n ESC Z ByteUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` ESC a n Hex PositionESC c5 n ESC d n ESC ESC x n B B B Memory Switch OFF GS n mGS * n1 n2 d n1 n2 D1 ...... Dn See Also Sample ProgramGS / m Hex Name Dot Density Vertical Direction Horizontal Direction1DH3AH GS H n Hex Printing PositionGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex Hex Mode GS n1 n2 n3GS a n Bit Status Item Addressed by ABSNot in use Thermal head is overheated Disabled for ASB may also have changed GS f n Hex Font1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Hex Code set a Code set B Code set CJAN-8 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes CODE93 CODE128GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Bluetooth Init Commands ExampleBlack Mark Function ESC l nDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 If YES is not chosen, the changed setting will not be lost Change IrDA MAX Speed ?Memory switches OFF0 ON1 Memory switch 8 =Change Print Density ? Programming Considerations Pin No Signal Direction Function Pin No. of Cable Serial InterfaceExplanation of Input/Output Signals 14, 15 pin Communicate mode settingElectrical Characteristics RS-232C CircuitInfrared Communication Specifications IrComm 3 Wire raw IrLPTMechanical Specification McbfPower Related Specifications BatteryAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU