Citizen Systems Model CMP-10 manual Disabled for ASB may also have changed

Page 55

BYTE 4

BIT7

BIT6

BIT5

BIT4

BIT3

BIT2

BIT1

BIT0

Not in use (0)

Not in use (0)

Not in use (0)

Not in use (0)

Not in use (1)

Not in use (0)

Not in use (0)

Not in use (0)

[Caution]	¥	If any status item is enabled, the status is sent to the host when this command is
		executed. After that time on, the status is sent each time an enabled status item
		changes. Because each status item represents the current condition, status items
		disabled for ASB may also have changed.
	¥	The ASB function is disabled if all status items are disabled.
	¥	The printer sends 4 bytes of status shown in the tables below, without checking
		whether the host is ready to receive or busy. The 4 bytes of status is a continuous
		string except for XOFF code.
	¥	Because this command is executed when data is mapped in the receive buffer,
		there may be a delay between command receiving and status sending depending
		on the condition of the receive buffer.
	¥	Even if the printer is excluded from the selection of peripheral equipment (ESC =),
		the 4 bytes of status is sent to the host whenever status changes.

Ñ 53 Ñ

Image 55

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU