Citizen Systems Model CMP-10 manual Setup menu function After Ver2.20

Page 69

4. Setup menu function (After Ver2.20)

Make sure the printer power is off. Press ON/OFF switch and keep pressed for about 5 seconds until .LED is changed to red and leave the switch. Then buzzer beeps and printer prints current setting and goes to setup menu as follows.

Example

DISCOVERABILITY:

YES

PAIRING INFO SAVING:

YES

MEMORY SWITCHES:

00000000

BAUD RATE:

9600

POWER OFF TIME:

10 min

PRINT DENSITY:

100%

MAX IrDA SPEED 57600:

NO

SETUP MENU

<ON/OFF> - NO, <LF> - YES

CHANGE DISCOVERABILITY ?

The setting can be done by choosing NO (ON/OFF switch) or YES (LF switch) against coming up questions. The details of each menu as follows.

(Following items A and B are shown when Bluetooth function is available.)

A. CHANGE DISCOVERABILITY ?

If you want to change the discoverability setting of Bluetooth, choose YES here. If not, choose NO and go to next item.

If you choose YES, another question ÒSET DISCOVERABILITY ON ?Ó shows up. Choose YES for DISCOVERABILITY ON or NO for DISCOVERABILITY OFF and go to next item.

However, even if the setting is YES, discoverability becomes off by pairing (bonding). Default setting is YES (Discoverable).

The setting change does not affect the unit without Bluetooth module.

B. CHANGE PAIRING INFO SAVING ?

If you want to change the setting of enable/disable pairing information saving, choose YES here. If not, choose NO and go to next item.

If you choose YES, another question ÒPAIRING INFO SAVING ON ?Ó shows up then Choose YES for Enable pairing information saving or choose NO for disabling pairing information saving and go to next item. Default setting is YES (enable pairing information saving)

The setting change does not affect the unit without Bluetooth module. (Supplementary notes)

This setting must be YES for pairing (bonding). If the pairing is enabled, you can set authentication or encryption and communicated with paired device becomes smooth.

If the condition for authentication is cleared, PIN code(PASS Key) is required to enter at the first time to communicate to the host machine. The default pin code is last 4 digit of BD address of Bluetooth module. BD address is 12 digit number printed on self test as Address. When you enter the PIN code, please use capital letter for A-F.

C. CHANGE MEMORY SWITCHES ?

If you want to change memory switch setting, choose YES here and if not, choose NO and go to next item. If you choose YES, questions like ÒSET SWITCH 1 ?Ó show up. Question is repeated from SWITCH 1 to SWTICH 8.

If you want to set the memory switch value to 1, choose YES. If you want to set the memory switch value to 0, choose NO. After choosing the value of SWTICH 8, next menu item is printed.

Default value of all memory switches is 0.

Ñ 67 Ñ

Image 69
Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H GS LGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC J n ESC R nHex Character Set ESC T ESC S nHex Speed bps Model CMP-10 VerHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnJAN-8 CODE93 CODE128GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU