Citizen Systems Model CMP-10 manual ESC c5 n, Hex Condition

Page 39

ESC c5 n

[Function]

Enabling/Disabling Panel Switches

[Code]

<1B>H<63>H<35>H<n>

[Range]

{0 =< n =< FF(Hex)}

[Outline]

Selecting the LF switch valid/invalid.

 

¥

ÒnÓ is valid only in the lowest bit (n0).

 

 

 

 

 

 

 

 

n (Hex)

Condition

 

 

 

0

LFSW valid.

 

 

 

 

 

 

 

 

1

LFSW invalid.

[Caution]

¥

When the panel switch is disabled with this command, the LF switch is disabled.

 

 

 

Therefore, the paper cannot be fed by operating the LF switch.

 

¥

When LF switch is set to Invalid, it cannot be cleared by the Initialize command

 

 

 

(ESC @) but is cleared by turning power off.

[Default]

The initial value of n is Ò0Ó.

[Sample Program]

 

 

 

 

PRINT #1, CHR$ (&H1B) + “c5” + CHR$ (0); ……When enabling the LF switch

PRINT #1, CHR$ (&H1B) + “c5” + CHR$ (1); ……When disabling the LF switch

Ñ 37 Ñ

Image 39
Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H GS LGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC J n ESC R nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU