Citizen Systems Model CMP-10 manual Power Related Specifications, Battery

Page 79

9.POWER RELATED SPECIFICATIONS

9.1Battery

(1)	Battery type	Lithium-ion battery pack
(2)	Maximum capacity	2000 mAh
(3)	Number of sells	2
(4)	Maximum output voltage	4.2V/Cell
(5)	Cut-off voltage	2.75V/Cell
(6)	Standard charge	1000 mA, 23¼C, 4.2V/Cell, 3 hours charge
(7)	Initial capacity	1950 mAh or more
		(After standard charge and discharge 400 mA till cut off at 23¼C,
		then measure the capacity)
(8)	Initial impedance	100m ohm or less
(9)	Cycle life capacity	1400 mAh or more
		(Repeat the routine - Standard charge + discharge 2000 mA till cut-off Ð
		299 times and leave one day, then measure in same condition as initial
		capacity)
(10)	Discharge by temperature	Ð10¼C 50%
		0¼C	80%
		23¼C	100%
		45¼C	100%
		(After standard charge and discharge 1000 mA till cut-off)
(11)	Storage	1600 mAh or more
		(After standard charge, keep it at 23¼C in 30 days then discharge
		1000 mA at 23¼C till cut-off)

9.2 Power Management

(1)	Printable lines	40,000 lines or more
		(Room temperature, full charge, ASCII slide pattern printing)
(2)	Auto power off time	5 minutes (can be changed between 1 and 60 minutes)
(3)	Low battery detection voltage	6.7V
(4)	Battery release voltage	5.5V

9.3Power Consumption

Average	1.45A (ASCII slide pattern printing)
Peak	2A
Stand-by	80 mA

Ñ 77 Ñ

Image 79

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU