Citizen Systems Model CMP-10 manual ESC E n, Hex Type

Page 27

ESC E n

[Function]	Specifying/canceling highlighting
[Code]	<1B>H<45>H<n>
[Range]	{0 =< n =< FF(Hex)}
[Outline]	Specifying/canceling the highlighting characters.
	¥ ÒnÓ is valid only for the lowest bit (n0).

	n (Hex)		Type
	0	Canceling highlighting.

	1	Specifying highlighting.
	¥ This is effective only for font A (12 ⋅ 24 dots)
	¥ Dot configuration of a highlighted character includes one extra dot added at its
	side.
[Caution]	The double printing and highlighted character printing commands provide exactly
	the same operation.
[Default]	n = 0
[See Also]	ESC !
[Sample Program]
	PRINT #1, CHR$ (&H1B) + “E” + CHR$ (0);
	PRINT #1, “AAABBB” + CHR$ (&HA);
	PRINT #1, CHR$ (&H1B) + “E” + CHR$ (1);
	PRINT #1, “AAABBB” + CHR$ (&HA);
[Print Results]
	A A A B B B		← Highlighting canceled
	AAA B B B		← Highlighting canceled

Ñ 25 Ñ

Image 27

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H GS LGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC J n ESC R nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU