Citizen Systems Model CMP-10 manual GS L nL nH

Page 49

GS L nL nH

[Function]

Setting the left margin

[Code]

<1D>H<4C>H<nL><nH>

[Range]

{0 =< nL =< FF(Hex)}

 

{0 =< nH =< FF(Hex)}

[Outline]

This command sets the left margin specified by nL and nH. The value of the left

 

margin is [(nL + nH 256) 1/203] inches.

[Caution]

¥ This command only works when it is entered at the beginning of a line.

 

¥ The maximum settable left margin is equal to the horizontal printable area. A

 

setting greater than this maximum is trimmed to the maximum.

 

¥ When mapping character data, if the print area specified is not wide enough to

 

accommodate one character of the current font, only the line for that character

 

data is handled as follows:

 

(1) The print area is extended toward the right to be equivalent to one character of

 

the current font, but not wider than the printable area.

 

(2) If an area for one character cannot be provided as a result of step (1), the print

 

area is extended toward the left. (So, the left margin is decreased.)

 

¥ When mapping non-character data (Bit image, downloaded bit image, or bar code),

 

if the print area specified is narrower than 9-bits, only the line for that data is handled

 

as follows:

 

(1) The print area is extended toward the left (So, the left margin is decreased)

 

until it is 9-dot wide, but not wider than the printable area.

[Default]

nL = 0, nH = 0

Ñ 47 Ñ

Image 49
Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set ESC T ESC S nHex Speed bps Model CMP-10 VerHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnJAN-8 CODE93 CODE128GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU