Citizen Systems Model CMP-10 manual 1DH3AH

Page 47

GS :

[Function]	Starting/Ending Macro Definition
[Code]	<1D>H<3A>H
[Outline]	Specifying starting/ending macro definition.
	Means termination when received while defining a macro.
[Caution]	¥ Maximum content available for macro definition is 3328 bytes.
	¥ A portion exceeding 3328 bytes is not defined.
	¥ Even with ESC @ (initialization of the printer) having been executed, defined content
	is not cleared. Therefore, it is possible to include ESC @ into the content of macro
	definition.
	¥ Normal printing operation is carried out even while in macro definition.
[Default]	Initially, Macro is not specified.
[See Also]	GS ^
[Sample Program]
	PRINT #1, CHR$ (&H1D) + “: “ ;
	PRINT #1, “+–––+” + CHR$ (&HA);
	PRINT #1, “ “ + CHR$ (&HA);
	PRINT #1, “+–––+” + CHR$ (&HA);
	PRINT #1, CHR$ (&H1D) + “: “;
	PRINT #1, CHR$ (&H1D) + “ ^ “;
	PRINT #1, CHR$ (2) + CHR$ (10);
	PRINT #1, CHR$ (0);
[Print Results]
		>
			Normal Printing during Macro Definition
		>

		>
			Printing during Macro Execution
			Printing during Macro Execution

		>

Ñ 45 Ñ

Image 47

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS W GS HGS L Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n Hex Character Set ESC J nESC R n Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsUL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard