Citizen Systems Model CMP-10 manual B B B

Page 43

ESC { n

[Function]	Specifying/Canceling the Inverted Characters
[Code]	<1B>H<7B>H<n>
[Range]	{0 =< n =< FF(Hex)}
[Outline]	Specifying/canceling inverted characters.
	¥ ÒnÓ is valid only for the lowest bit (n0).

	n (Hex)	Condition

0Canceling inverted characters.

1 Specifying inverted characters.

[Caution]	¥	Inverted-printing means printing the line at 180¡ turned.
	¥	This is valid only when this is specified at the beginning of a line.
[Default]	¥	The initial value of n is Ò0Ó.
[Sample Program]

PRINT #1, CHR$ (&H1B) + “{“ + CHR$ (0);

PRINT #1, “AAAAA” + CHR$ (&HA);

PRINT #1, “BBBBB” + CHR$ (&HA);

PRINT #1, CHR$ (&H1B) + “{“ + CHR$ (1);

PRINT #1, “AAAAA” + CHR$ (&HA);

PRINT #1, “BBBBB” + CHR$ (&HA);

[Print Results]

A A A A A

Inversion Canceled

B B B B B

	Inversion Specified	B B B B B
	Inversion Specified	A A A A A
		A A A A A

∨

Paper Feed

Direction

Ñ 41 Ñ

Image 43

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS L GS HGS W Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU