Citizen Systems Model CMP-10 manual ESC \ n1 n2, Function

Page 36

ESC \ n1 n2

[Function]

Specifying the relative positions

[Code]

<1B>H<5C>H<n1><n2>

[Range]

{0 =< n1 =< 255}

 

{0 =< n2 =< 255}

[Outline]

The printing start position is specified in the number of dots (1/203 inch unit) from

 

the current position.

 

¥ Rightward direction is taken as plus and leftward direction as minus.

 

¥ To specify N dot in minus (left) direction, use a complement of N for assignment.

 

¥ N dots = 65536 Ð N

 

¥ The number of dots is divided by 256, whose quotient is taken as n2 and the residual

 

as n1.

[Caution]

Specifying exceeding the top of line or the end of line is ignored.

[See Also]

ESC $

[Sample Program]

See Sample Program and Print Results for ESC $.

ESC _

[Function]

Setting the printer in default state

[Code]

<1B>H<5F>H

[Outline]

Sets the printer in default state. The default state is as follows:

 

¥

All printing attributes like underline, rotating etc. are cleared.

 

¥

Internal font A (12 24) is selected.

 

¥

Pitch between lines is 1/6 inch.

 

¥

Pitch between characters is 0.

 

¥

Barcode height is 162 dots, and barcode width is 3.

 

¥

All downloaded fonts and bit images are cleared.

 

¥

Print density is 100%.

 

¥

Communication speed is set to 9600 bps.

 

¥

Auto power-off time is set at 5 min.

 

¥

Memory switch is set to Òall 0Ó.

[See Also]

ESC @

Ñ 34 Ñ

Image 36
Contents Command Reference Revision CMP-10 Command SET Code Command FunctionGS H GS LGS W Command Details Xxxx ALLBEL Sample Program Print Results0AH ESC RS Default Sample Program ESC SP nDefault See Also ESC ! nBit Function Value END ESC $ n1 n2 ESC % n Initialize command ESC & m n1 n2 d kHex Mode Vertical Direction Horizontal Direction Dots ESC * m n1 n2 d kMax. Dots IMG1 Page ESC + ESC nHex Type ESC ESC 3 n ESC = n Bit Equipment Value21 Ñ ESC ? n Hex TrackESC @ ESC D n k NUL See Also Sample Program Print ResultsESC E n ESC G n ESC J n ESC R nHex Character Set ESC S n ESC THex Speed bps Model CMP-10 VerESC V n Hex ConditionESC Y n ESC Z ByteUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` ESC a n Hex PositionESC c5 n ESC d n ESC ESC x n B B B Memory Switch OFF GS n mGS * n1 n2 d n1 n2 D1 ...... Dn See Also Sample ProgramGS / m Hex Name Dot Density Vertical Direction Horizontal Direction1DH3AH GS H n Hex Printing PositionGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex Hex Mode GS n1 n2 n3GS a n Bit Status Item Addressed by ABSNot in use Thermal head is overheated Disabled for ASB may also have changed GS f n Hex Font1DH68Hn GS k m d1 ..... dk NUL GS k m n d1 ...... dn Bar code system Range of k Range of dBar code system Range of n Range of d For Standard Mode ForDescription of Bar Codes JAN-8EAN Hex Code set a Code set B Code set CType Print Sample Outline of Symbol Max. Column Descriptionof Bar CodesJAN-8 CODE93 CODE128GS w nL nH AT command Function Factory default AT*PAIRINFO=0AT*PAIRINFO=1 Bluetooth Init Commands ExampleBlack Mark Function ESC l nDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 If YES is not chosen, the changed setting will not be lost Change IrDA MAX Speed ?Memory switches OFF0 ON1 Memory switch 8 =Change Print Density ? Programming Considerations Pin No Signal Direction Function Pin No. of Cable Serial InterfaceExplanation of Input/Output Signals 14, 15 pin Communicate mode settingElectrical Characteristics RS-232C CircuitInfrared Communication Specifications IrComm 3 Wire raw IrLPTMechanical Specification McbfPower Related Specifications BatteryAC Adaptor EMI StandardUL, C-UL, PSE 10AD-JU