Citizen Systems Model CMP-10 manual 21 Ñ

Page 23

ESC > n

[Function]

Saving current setting

 

[Code]

<1B>H<3E>H<n>

 

[Range]

n = 0 or 1

 

[Outline]

This command saves International character, Serial port baud rate, Print density, Auto

 

power off time and maximum speed at Infrared communication to NV memory so

 

that the setting can be resumed automatically when power on after setting data on

 

RAM memory is gone by like battery is disconnected.

 

 

 

 

n (Hex)

Type

0Max speed at Infrared communication is 115200 bps.

1 Max speed at Infrared communication is 57600 bps.

[Caution]

Do NOT use this command frequently.

 

NEVER turn the printer off during command is running. Otherwise there is a risk to

 

lose the firmware updating function.

 

Power is turned off automatically when setting is saved.

[Default]

n = 0

[See Also]

ESC R, ESC S, ESC Y, ESC x

Ñ 21 Ñ

Image 23
Contents Command Reference Revision Code Command Function CMP-10 Command SETGS W GS HGS L Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = n21 Ñ Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n Hex Character Set ESC J nESC R n Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C HexCODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Example Bluetooth Init CommandsESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lostMemory switch 8 = Memory switches OFF0 ON1Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsMcbf Mechanical SpecificationBattery Power Related SpecificationsUL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard