Panasonic WV-CU650 Alarm Control, System Controller Behavior during the Alarm Mode, Alarm Reset

Page 44

ALARM CONTROL

■System Controller Behavior during the Alarm Mode

When an alarm signal is input to cameras or system units, this system controller is notified that an alarm has been activated. Then, the ALARM indicator will blink. During the alarm mode, “Alarm” sign will blink on the LCD, and the camera number is displayed as “- - -“.

Mon01 Cam--- HD316

Alarm

When an alarm is automatically canceled (=alarm auto reset mode), “Alarm” sign changes from blinking to steady light, and the LCD display returns to the normal status.

■Alarm Reset

You can cancel the alarm mode (“Alarm” sign is blinking.) or alarm auto reset mode (The ALARM indicator is light- ing.). The alarm inputs to all the system units will be reset all together.

Press ALM RESET/ALM ALL RESET button.

The alarm mode or alarm auto reset mode of all the system units will be cancelled, and the ALARM indicator will go out.

Notes:

•Alarm behaviors differ depending on connected system units. Refer to the operating instructions of system units.

•You cannot cancel the alarm mode or alarm auto reset mode of each system unit one by one.

■Alarm Suspension

You can temporarily stop alarm inputs to all the system units in the following procedure.

1.Press the ALARM/ALM SUSPEND button while holding down the SHIFT button.

The alarm inputs will be suspended and the ALM SUS- PEND indicator will light up.

2.To cancel the alarm suspension mode, press ALARM/ALM SUSPEND button again while holding down the SHIFT button. The alarm suspension mode will be canceled, and the ALM SUSPEND indicator will go out.

Note: You cannot suspend each alarm input one by one. The alarm inputs to all the system units will be suspended all together.

■Alarm History Search

To play back a desired alarm image, the alarm history table of selected system unit can be displayed. The following procedure is available when the selected system unit can display the alarm history table.

Note: WJ-HD300 Series does not support alarm history search.

●How to Display Alarm History Tables

1.Press the ALM RECALL button.

“Alarm Recall” sign will appear on the LCD, and the alarm history table will be displayed on an active moni- tor.

Alarm Recall

2.Perform operations while watching the active monitor.

Note: The operation details differ depending on recorders. Refer to pp. 45 to 46.

Controls commonly available

<Main unit>

Shuttle ring clockwise or counterclockwise:

•Changes the search list display. (For example, Record list ↔ Thumbnail Display ↔ Record List …)

•Moves the cursor. (Available for WJ-HD500 or WJ- HD200 Series)

JogDial clockwise or counterclockwise:

•Moves the cursor.

•Changes the selected parameter. (Available for WJ- HD500 or WJ-HD200 Series)

+button: Increases a numeric value.

–button: Decreases a numeric value. Numeric buttons: Enters numeric parameters.

CAM (SET) button: Determines the selected parame- ter.

MON (ESC) or EXIT button: Closes the search list dis- play.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Operating Instructions English Version Important Safety Instructions Contents Features PrefacePrecautions Limitation of LiabilityDo not drop metallic parts through slots Do not attempt to disassemble the applianceDocument Convention Notification about System UnitsMain Unit Front View0Alarm recall button ALM Recall Camera function/System function button1On-screen display button OSD 2Monitor lock/Logout button MON LOCK/LOGOUT#3Preset/Program preset button PRESET/PGM #9Adjustment button Adjust@8Shuttle hold button Shuttle Hold @9History button HistoryRear View 3D Joystick Unit Mon02 Cam016 HD316 Default Status LCD Display After LoginLCD Display Descriptions Blinking Main Menu Menu FunctionsSub Menu Menu Functions Controller No.1 No Exist Error Messages Displayed on the LCDInvalid Mon02 Cam016 HD316 BusyInstallations and Connections Basic System ConnectionsAdjustment of 3D Joystick Connection with the 3D Joystick UnitSetup Procedures Hardware Setup ProceduresMode Switch Setting Controller NO. Switch SettingSetup Procedures Firmware Administrator Password EntrySetting Modes Setting Mode DescriptionOperation All ResetPS·Data Communication Setting Baud Rate Setting Wait Time Setting Parity Bit SettingStop Bit Setting Group Address Setting for System Controller Group Address Setting for System UnitsTo Change the Administrator Password Database Copy PS·Data Operator Password Check Data Base Rx Mode Completed Sum=1733PSD Password Check Admin Password PSD Password Check Admin Password ∗ ∗ ∗ ∗ ∗Before Operation Power-onPower-off LCD/BUZZER Adjustment Buzzer AlarmBasic Operation Flow LCD BrightOperation Start Login If You Have Forgotten the Login Password Operation Start Auto LoginPS Data Mode Auto Login Logout PS·Data Mode No UserRecorder Selection Unit SelectionSystem Unit Selection Monitor Selection Camera SelectionSystem Unit Control Multiscreen DisplayElectronic Zooming Tour Sequence/Group SequenceSystem Function Control How to Display Search Lists Recorder ControlManual Recording Search PlaybackSearch Mode HD300 List Text Copy Nr-A Cp-A Cpy1 Cpy2 Example of searching filter display and settingsOperation WJ-HD300 Series Available buttons and functionsSearch Mode HD500 Edit Group Alm Copy Search Mode HD500 DriveOperation WJ-HD500 Series LCD displaySearch Mode HD200 Time & Date Search PlaybackOperation WJ-HD200 Series Mmm/DD/YYYY Hhmm Mar/16/2004 0132 PMOther Available Functions Camera Control Camera Panning/Tilting ControlZooming Control Lens Iris Control Camera Function Control Preset Position Control Home Position Control Camera Position Control Camera Selection RecallWiper Control Mon02 Cam001 HD316 F1 F2 F3 F4 Mon01 C-P011 HD316Operating Procedure Latch mode Operating Procedure Momentary modeDefroster Control Auxiliary ControlAlarm Control System Controller Behavior during the Alarm ModeAlarm Reset Alarm SuspensionAlarm Recall HD500 Edit Group Copy Operation WJ-HD100 Series Alarm Recall HD200 EditAlarm Recall HD100 Menu Function Descriptions Menu FlowRecorder Functions HDD Menu Function CategoriesCamera Functions CAM System Functions SYS ControllerJoystick Button Functions J/S Menu To Recall Menu Functions To Assign Menu Functions to Function Buttons Mon02 Cam128 HD316 F1 F2 F3 F4 Camera Setup Off Rst To Assign Menu Functions to Joystick Function ButtonsTo Recall Button Functions and Joystick Button Functions Camera Function Assign a Code=Function Check Camera Setup 101 To Check Button Functions and Joystick Button FunctionsCamera Setup Auto ModeBW Mode Menu Function DetailsBW Mode 103 Off Auto1 Auto2 Patrol LearnPatrol Learn 104 Start Stop Patrol Learn Pre03 Start StopAuto Pan Setup and Activation Repeat Playback Setting WJ-HD300 Series OnlyRecorder Functions Disk Selection WJ-HD300 Series OnlySystem Setup System FunctionsFiltering ON/OFF WJ-HD300 Series Only Displaying Camera and Playback Image WJ-HD500 Series OnlyMux Still Enter F1 Button 304Mux Still 305 Input Still CH Time & Date Search Display Pattern Camera CleaningController Functions Auto Login/Logout Setup Operator Registration or Change Function Level Setting Camera Level Setting Camera Position Registration or Clearing Associating Camera Numbers with Unit Numbers Associating Recorder Numbers with Unit Numbers LCD Title Editing System Function Joystick Button FunctionsCamera Function Auto Pan Camera SortCamera Sequence Patrol PlayIris Reset Home PositionAuto Focus Camera +1Recorded-image Copy WJ-HD500 Series Only CameraRepeat Playback WJ-HD300 Series Only Alarm Search WJ-HD200 Series / WJ-HD100 Series Multiscreen DisplayTroubleshooting Problem Check item and Remedy ReferenceProblem Check item and Remedy Reference Specifications Standard AccessoriesSystem Controller Data PortPage 2004
Top Page Image Contents