Panasonic WV-CU650 operating instructions Camera Position Registration or Clearing

Page 65

Camera

Table3

406

Cam001

 

=E

4.Select a desired camera channel by performing one of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

•Enter the camera number with the numeric buttons.

Camera

Table3

406

Cam064

 

=E

Note: You can select a camera channel from 1 to 256.

5.Rotate the shuttle ring clockwise or move the 3D joy- stick to the right. The cursor will jump to the next item.

Camera

Table3

406

Cam064

 

=

 

 

E

Note: To return to Step 4, rotate the shuttle ring coun- terclockwise or move the 3D joystick to the left.

6.Select E (= Enabled) or D (= Disabled) by performing either of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

Camera

Table3

406

Cam064

 

=

 

 

D

E (= Enabled): The operator can display the cam- era image on the monitor and control panning/tilt- ing. (VIEW & CONTROL)

D (= Disabled): The operator can display the cam- era image on the monitor, but cannot control the panning/tilting. (VIEW ONLY)

Note: To change the settings of other cameras, repeat Step 4 to 6.

7.Press the ENTER or CAM (SET) button. “Set OK?” will appear on the LCD.

Camera Table3

406

 

Set OK?

 

 

Note: To cancel the setting, press the EXIT or MON (ESC) button. The LCD display will return to Step 6.

8.Press the ENTER or CAM (SET) button again.

The camera levels will be set for the selected table. “Memory” will appear on the LCD for a few seconds, and the LCD display will return to Step 1.

Camera Table3

406

 

Memory

 

 

●Camera Position Registration or Clearing

This system controller can memorize camera position num- bers, which are the combination of camera numbers and preset position numbers. By entering a camera position number, you can select a desired camera and preset posi- tion at a time. You can register up to 1 000 camera position numbers.

1.Display “Cam Posi Map” sub menu. (Refer to Step 1 to 4 of p. 51 To Recall Menu Functions.)

Cam Posi

Map

407

Cam-P001

C---

Pre--

2.Select a camera position number to register by per- forming one of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

•Enter the camera position number with the numeric buttons.

Cam Posi

Map

407

Cam-P016

C---

Pre--

Notes:

•To register a new position number, press the numeric buttons.

•You can select a camera position number from 0 to 999.

3.Rotate the shuttle ring clockwise or move the 3D joy- stick to the right. The cursor will jump to the next item.

Note: To return to Step 2, rotate the shuttle ring coun- terclockwise or move the 3D joystick to the left.

4.Select a desired camera channel by performing one of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

•Enter the camera number with the numeric buttons.

Cam Posi

Map

407

Cam-P016

 

C005

 

Pre--

Note: You can select a camera channel from 1 to 999.

5.Rotate the shuttle ring clockwise or move the 3D joy- stick to the right. The cursor will jump to the next item.

Note: To return to Step 4, rotate the shuttle ring coun-

terclockwise or move the 3D joystick to the left.

65

 

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Operating Instructions English Version Important Safety Instructions Contents Preface FeaturesLimitation of Liability PrecautionsDo not drop metallic parts through slots Do not attempt to disassemble the applianceNotification about System Units Document ConventionFront View Main UnitCamera function/System function button 0Alarm recall button ALM Recall1On-screen display button OSD 2Monitor lock/Logout button MON LOCK/LOGOUT#9Adjustment button Adjust #3Preset/Program preset button PRESET/PGM@8Shuttle hold button Shuttle Hold @9History button HistoryRear View 3D Joystick Unit Mon02 Cam016 HD316 Default Status LCD Display After LoginLCD Display Descriptions Blinking Main Menu Menu FunctionsSub Menu Menu Functions Messages Displayed on the LCD Controller No.1 No Exist ErrorInvalid Mon02 Cam016 HD316 BusyBasic System Connections Installations and ConnectionsConnection with the 3D Joystick Unit Adjustment of 3D JoystickSetup Procedures Setup Procedures HardwareMode Switch Setting Controller NO. Switch SettingAdministrator Password Entry Setup Procedures FirmwareSetting Modes Setting Mode DescriptionOperation All ResetPS·Data Communication Setting Baud Rate Setting Wait Time Setting Parity Bit SettingStop Bit Setting Group Address Setting for System Units Group Address Setting for System ControllerTo Change the Administrator Password Database Copy Data Base Rx Mode Completed Sum=1733 PS·Data Operator Password CheckPSD Password Check Admin Password PSD Password Check Admin Password ∗ ∗ ∗ ∗ ∗Before Operation Power-onPower-off Buzzer Alarm LCD/BUZZER AdjustmentBasic Operation Flow LCD BrightOperation Start Login Operation Start Auto Login If You Have Forgotten the Login PasswordPS Data Mode Auto Login Logout PS·Data Mode No UserRecorder Selection Unit SelectionSystem Unit Selection Camera Selection Monitor SelectionMultiscreen Display System Unit ControlElectronic Zooming Tour Sequence/Group SequenceSystem Function Control Recorder Control How to Display Search ListsManual Recording Search PlaybackExample of searching filter display and settings Search Mode HD300 List Text Copy Nr-A Cp-A Cpy1 Cpy2Operation WJ-HD300 Series Available buttons and functionsSearch Mode HD500 Drive Search Mode HD500 Edit Group Alm CopyOperation WJ-HD500 Series LCD displayTime & Date Search Playback Search Mode HD200Operation WJ-HD200 Series Mmm/DD/YYYY Hhmm Mar/16/2004 0132 PMOther Available Functions Camera Panning/Tilting Control Camera ControlZooming Control Lens Iris ControlCamera Function Control Preset Position ControlHome Position Control Camera Selection Recall Camera Position ControlWiper Control Mon02 Cam001 HD316 F1 F2 F3 F4 Mon01 C-P011 HD316Operating Procedure Momentary mode Operating Procedure Latch modeDefroster Control Auxiliary ControlSystem Controller Behavior during the Alarm Mode Alarm ControlAlarm Reset Alarm SuspensionAlarm Recall HD500 Edit Group Copy Operation WJ-HD100 Series Alarm Recall HD200 EditAlarm Recall HD100 Menu Flow Menu Function DescriptionsRecorder Functions HDD Menu Function CategoriesCamera Functions CAM Controller System Functions SYSJoystick Button Functions J/S Menu To Recall Menu Functions To Assign Menu Functions to Function Buttons To Assign Menu Functions to Joystick Function Buttons Mon02 Cam128 HD316 F1 F2 F3 F4 Camera Setup Off RstTo Recall Button Functions and Joystick Button Functions Camera Function Assign a Code=To Check Button Functions and Joystick Button Functions Function Check Camera Setup 101Auto Mode Camera SetupBW Mode Menu Function DetailsPatrol Learn BW Mode 103 Off Auto1 Auto2Patrol Learn 104 Start Stop Patrol Learn Pre03 Start StopRepeat Playback Setting WJ-HD300 Series Only Auto Pan Setup and ActivationRecorder Functions Disk Selection WJ-HD300 Series OnlySystem Functions System SetupFiltering ON/OFF WJ-HD300 Series Only Displaying Camera and Playback Image WJ-HD500 Series OnlyMux Still Enter F1 Button 304Mux Still 305 Input Still CH Time & Date Search Display Pattern Camera CleaningController Functions Auto Login/Logout Setup Operator Registration or Change Function Level Setting Camera Level Setting Camera Position Registration or Clearing Associating Camera Numbers with Unit Numbers Associating Recorder Numbers with Unit Numbers LCD Title Editing System Function Joystick Button FunctionsCamera Function Camera Sort Auto PanCamera Sequence Patrol PlayHome Position Iris ResetAuto Focus Camera +1Recorded-image Copy WJ-HD500 Series Only CameraRepeat Playback WJ-HD300 Series Only Multiscreen Display Alarm Search WJ-HD200 Series / WJ-HD100 SeriesProblem Check item and Remedy Reference TroubleshootingProblem Check item and Remedy Reference Standard Accessories SpecificationsSystem Controller Data PortPage 2004
Top Page Image Contents