Panasonic WV-CU650 Controller Functions, Camera Cleaning, Time & Date Search Display Pattern

Page 60

3.Press the F1 button.

•The still mode will be activated for the selected camera channel.

•The specified camera channel will blink on the LCD for a few seconds, and the LCD display will return to Step 1.

Mux

Still

305

 

 

Still

CH=__9

Mux

Still

305

 

 

 

 

 

 

Still

CH=All

Note: To return the multiscreen monitor display from the still mode to moving mode, perform Step 1 to 3 again.

■Controller Functions

●Camera Cleaning

1.Display “Camera Cleaning” sub menu. (Refer to Step 1 to 4 of p. 51 To Recall Menu Functions.)

Camera Cleaning 401

Start Cancel 001-256

F1 F2 F3 F4

Note: To return the cursor to the previous item, rotate the shuttle ring counterclockwise or move the 3D joystick to the left.

5.Press the F1 button.

Camera cleaning will be cleared from the first to the last camera you have set.

During the cleaning, the current channel number will be displayed on the LCD.

Camera Cleaning 401

Start Cancel Cam028

When the all cameras have started to be cleaned, “End” will appear on the LCD.

Camera

Cleaning

401

Start

Cancel

End

Notes:

•To quit the cleaning, press the F2 button.

•It may take a few minutes since “End” appears on the LCD until camera cleaning ends.

•If you have selected a lower channel for the last camera than the first camera, “Invalid” will appear on the LCD.

Invalid

2.Select the camera to clean first by performing one of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

•Enter the camera number with the numeric buttons.

Camera Cleaning 401

Start Cancel 003-256

F1

F2

F3

F4

3.Rotate the shuttle ring clockwise or move the 3D joy- stick to the right. The cursor will jump to the next item.

4.Select the camera to clean last by performing one of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

•Enter the camera number with the numeric buttons.

Camera Cleaning 401

Start Cancel 003-064

F1

F2

F3

F4

60

In this case, select a higher camera channel for the last camera.

●Time & Date Search Display Pattern

You can set up the clock display pattern of the LCD for the time & date search. You can select a desired one from 10 patterns.

1.Display “Time & Date Type” sub menu. (Refer to Step 1 to 4 of p. 51 To Recall Menu Functions.)

Time&Date Type 402

Mmm/DD/YYYY HH:MM 12

2.Select a desired display pattern by performing either of the following.

•Rotate the JogDial clockwise or counterclockwise.

•Press the + or – button.

Time&Date Type 402

DD/MM/YYYY HH:MM 24

The following patterns are available.

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Operating Instructions English Version Important Safety Instructions Contents Features PrefacePrecautions Limitation of LiabilityDo not drop metallic parts through slots Do not attempt to disassemble the applianceDocument Convention Notification about System UnitsMain Unit Front View0Alarm recall button ALM Recall Camera function/System function button1On-screen display button OSD 2Monitor lock/Logout button MON LOCK/LOGOUT#3Preset/Program preset button PRESET/PGM #9Adjustment button Adjust@8Shuttle hold button Shuttle Hold @9History button HistoryRear View 3D Joystick Unit Default Status LCD Display After Login LCD Display DescriptionsMon02 Cam016 HD316 Main Menu Menu Functions Sub Menu Menu FunctionsBlinking Controller No.1 No Exist Error Messages Displayed on the LCDInvalid Mon02 Cam016 HD316 BusyInstallations and Connections Basic System ConnectionsAdjustment of 3D Joystick Connection with the 3D Joystick UnitSetup Procedures Hardware Setup ProceduresMode Switch Setting Controller NO. Switch SettingSetup Procedures Firmware Administrator Password EntrySetting Modes Setting Mode DescriptionAll Reset PS·Data Communication SettingOperation Baud Rate Setting Parity Bit Setting Stop Bit SettingWait Time Setting Group Address Setting for System Controller Group Address Setting for System UnitsTo Change the Administrator Password Database Copy PS·Data Operator Password Check Data Base Rx Mode Completed Sum=1733PSD Password Check Admin Password PSD Password Check Admin Password ∗ ∗ ∗ ∗ ∗Power-on Power-offBefore Operation LCD/BUZZER Adjustment Buzzer AlarmBasic Operation Flow LCD BrightOperation Start Login If You Have Forgotten the Login Password Operation Start Auto LoginPS Data Mode Auto Login Logout PS·Data Mode No UserUnit Selection System Unit SelectionRecorder Selection Monitor Selection Camera SelectionSystem Unit Control Multiscreen DisplayElectronic Zooming Tour Sequence/Group SequenceSystem Function Control How to Display Search Lists Recorder ControlManual Recording Search PlaybackSearch Mode HD300 List Text Copy Nr-A Cp-A Cpy1 Cpy2 Example of searching filter display and settingsOperation WJ-HD300 Series Available buttons and functionsSearch Mode HD500 Edit Group Alm Copy Search Mode HD500 DriveOperation WJ-HD500 Series LCD displaySearch Mode HD200 Time & Date Search PlaybackOperation WJ-HD200 Series Mmm/DD/YYYY Hhmm Mar/16/2004 0132 PMOther Available Functions Camera Control Camera Panning/Tilting ControlZooming Control Lens Iris ControlPreset Position Control Home Position ControlCamera Function Control Camera Position Control Camera Selection RecallWiper Control Mon02 Cam001 HD316 F1 F2 F3 F4 Mon01 C-P011 HD316Operating Procedure Latch mode Operating Procedure Momentary modeDefroster Control Auxiliary ControlAlarm Control System Controller Behavior during the Alarm ModeAlarm Reset Alarm SuspensionAlarm Recall HD500 Edit Group Copy Alarm Recall HD200 Edit Alarm Recall HD100Operation WJ-HD100 Series Menu Function Descriptions Menu FlowMenu Function Categories Camera Functions CAMRecorder Functions HDD System Functions SYS ControllerJoystick Button Functions J/S Menu To Recall Menu Functions To Assign Menu Functions to Function Buttons Mon02 Cam128 HD316 F1 F2 F3 F4 Camera Setup Off Rst To Assign Menu Functions to Joystick Function ButtonsTo Recall Button Functions and Joystick Button Functions Camera Function Assign a Code=Function Check Camera Setup 101 To Check Button Functions and Joystick Button FunctionsCamera Setup Auto ModeBW Mode Menu Function DetailsBW Mode 103 Off Auto1 Auto2 Patrol LearnPatrol Learn 104 Start Stop Patrol Learn Pre03 Start StopAuto Pan Setup and Activation Repeat Playback Setting WJ-HD300 Series OnlyRecorder Functions Disk Selection WJ-HD300 Series OnlySystem Setup System FunctionsFiltering ON/OFF WJ-HD300 Series Only Displaying Camera and Playback Image WJ-HD500 Series Only304 Mux Still 305 Input Still CHMux Still Enter F1 Button Camera Cleaning Controller FunctionsTime & Date Search Display Pattern Auto Login/Logout Setup Operator Registration or Change Function Level Setting Camera Level Setting Camera Position Registration or Clearing Associating Camera Numbers with Unit Numbers Associating Recorder Numbers with Unit Numbers LCD Title Editing Joystick Button Functions Camera FunctionSystem Function Auto Pan Camera SortCamera Sequence Patrol PlayIris Reset Home PositionAuto Focus Camera +1Camera Repeat Playback WJ-HD300 Series OnlyRecorded-image Copy WJ-HD500 Series Only Alarm Search WJ-HD200 Series / WJ-HD100 Series Multiscreen DisplayTroubleshooting Problem Check item and Remedy ReferenceProblem Check item and Remedy Reference Specifications Standard AccessoriesSystem Controller Data PortPage 2004
Top Page Image Contents