Panasonic WV-CU650 Setup Procedures Hardware, Mode Switch Setting, Controller NO. Switch Setting

Page 18

SETUP PROCEDURES (HARDWARE)

■ Setup Procedures

2. Set the Line termination switch of other system con-

trollers to OFF.

 

 

 

 

 

 

 

Perform the setup as follows.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

1.Set the MODE switches.

You will set up the communication mode and line termi- nation ON/OFF of RS-485 communication. (Refer to MODE Switch Setting.)

2.Set CONTROLLER NO. switches.

You will perform this setting when using two or more system controllers in daisy chain connections. (Refer to CONTROLLER NO. Setting.)

3.Perform WV-CU650 setups after entering the administrator password.

You will perform the settings concerning password and communication between system controllers and other system units, etc. (Refer to p. 19.)

Note: Before performing WV-CU650 setups, you need to log into the system by entering the administrator pass- word. (Refer to p. 19.)

OFF

ON

System units

Line termination ON

Line termination OFF

Line termination OFF Line termination OFF Line termination ON

●Setting for Terminal Mode

Set the MODE Switch #1 and #5 to ON.

1 2 3 4 5 6 7 8

■MODE Switch Setting

You will perform the setting of the MODE switches at the rear panel.

Notes:

•Before the setting, turn off the system controller. (Refer to p. 27 Power-off.)

•Do not move the MODE switches to positions other than described in these illustrations. That may cause mal- function.

OFF

ON

Note: Refer to the following document for details on con- nections and operations.

Addendum for WV-CU650 and WJ-SX150 Series

■CONTROLLER NO. Switch Setting

You will determine controller-number settings by moving the CONTROLLER NO. switch at the rear panel.

●Setting for PS·Data Mode

If using only one system controller

Set the MODE Switch #5 to ON.

1 2 3 4 5 6 7 8

OFF

ON

MODE Switch #5 (Line termination switch)

If using two or more system controllers in daisy chain connections

1.Set the MODE Switch #5 of the system controller at the chain end to ON.

18

If using only one system controller

Maintain the switch setting as “1 (factory default position)”.

If using two or more system controllers in daisy chain connections

Up to 4 system controllers are connectable in the system. To avoid conflict, set the unique number for each system controller.

9

0

1

8

 

2

 

 

7

 

3

 

 

6

5

4

 

 

 

CONTROLLER No.

Notes:

•“0” and “9” are reserved numbers. They cannot be set for controller numbers.

•One of the system controllers must be set to "1".

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operating Instructions English Version Important Safety Instructions Contents Features PrefaceDo not drop metallic parts through slots PrecautionsLimitation of Liability Do not attempt to disassemble the applianceDocument Convention Notification about System UnitsMain Unit Front View1On-screen display button OSD 0Alarm recall button ALM RecallCamera function/System function button 2Monitor lock/Logout button MON LOCK/LOGOUT@8Shuttle hold button Shuttle Hold #3Preset/Program preset button PRESET/PGM#9Adjustment button Adjust @9History button HistoryRear View 3D Joystick Unit Default Status LCD Display After Login LCD Display DescriptionsMon02 Cam016 HD316 Main Menu Menu Functions Sub Menu Menu FunctionsBlinking Invalid Controller No.1 No Exist Error Messages Displayed on the LCD Mon02 Cam016 HD316 BusyInstallations and Connections Basic System ConnectionsAdjustment of 3D Joystick Connection with the 3D Joystick UnitMode Switch Setting Setup Procedures HardwareSetup Procedures Controller NO. Switch SettingSetting Modes Setup Procedures FirmwareAdministrator Password Entry Setting Mode DescriptionAll Reset PS·Data Communication SettingOperation Baud Rate Setting Parity Bit Setting Stop Bit SettingWait Time Setting Group Address Setting for System Controller Group Address Setting for System UnitsTo Change the Administrator Password Database Copy PSD Password Check Admin Password PS·Data Operator Password CheckData Base Rx Mode Completed Sum=1733 PSD Password Check Admin Password ∗ ∗ ∗ ∗ ∗Power-on Power-offBefore Operation Basic Operation Flow LCD/BUZZER AdjustmentBuzzer Alarm LCD BrightOperation Start Login PS Data Mode Auto Login If You Have Forgotten the Login PasswordOperation Start Auto Login Logout PS·Data Mode No UserUnit Selection System Unit SelectionRecorder Selection Monitor Selection Camera SelectionElectronic Zooming System Unit ControlMultiscreen Display Tour Sequence/Group SequenceSystem Function Control Manual Recording How to Display Search ListsRecorder Control Search PlaybackOperation WJ-HD300 Series Search Mode HD300 List Text Copy Nr-A Cp-A Cpy1 Cpy2Example of searching filter display and settings Available buttons and functionsOperation WJ-HD500 Series Search Mode HD500 Edit Group Alm CopySearch Mode HD500 Drive LCD displayOperation WJ-HD200 Series Search Mode HD200Time & Date Search Playback Mmm/DD/YYYY Hhmm Mar/16/2004 0132 PMOther Available Functions Zooming Control Camera ControlCamera Panning/Tilting Control Lens Iris ControlPreset Position Control Home Position ControlCamera Function Control Wiper Control Camera Position ControlCamera Selection Recall Mon02 Cam001 HD316 F1 F2 F3 F4 Mon01 C-P011 HD316Defroster Control Operating Procedure Latch modeOperating Procedure Momentary mode Auxiliary ControlAlarm Reset Alarm ControlSystem Controller Behavior during the Alarm Mode Alarm SuspensionAlarm Recall HD500 Edit Group Copy Alarm Recall HD200 Edit Alarm Recall HD100Operation WJ-HD100 Series Menu Function Descriptions Menu FlowMenu Function Categories Camera Functions CAMRecorder Functions HDD System Functions SYS ControllerJoystick Button Functions J/S Menu To Recall Menu Functions To Assign Menu Functions to Function Buttons To Recall Button Functions and Joystick Button Functions Mon02 Cam128 HD316 F1 F2 F3 F4 Camera Setup Off RstTo Assign Menu Functions to Joystick Function Buttons Camera Function Assign a Code=Function Check Camera Setup 101 To Check Button Functions and Joystick Button FunctionsBW Mode Camera SetupAuto Mode Menu Function DetailsPatrol Learn 104 Start Stop BW Mode 103 Off Auto1 Auto2Patrol Learn Patrol Learn Pre03 Start StopRecorder Functions Auto Pan Setup and ActivationRepeat Playback Setting WJ-HD300 Series Only Disk Selection WJ-HD300 Series OnlyFiltering ON/OFF WJ-HD300 Series Only System SetupSystem Functions Displaying Camera and Playback Image WJ-HD500 Series Only304 Mux Still 305 Input Still CHMux Still Enter F1 Button Camera Cleaning Controller FunctionsTime & Date Search Display Pattern Auto Login/Logout Setup Operator Registration or Change Function Level Setting Camera Level Setting Camera Position Registration or Clearing Associating Camera Numbers with Unit Numbers Associating Recorder Numbers with Unit Numbers LCD Title Editing Joystick Button Functions Camera FunctionSystem Function Camera Sequence Auto PanCamera Sort Patrol PlayAuto Focus Iris ResetHome Position Camera +1Camera Repeat Playback WJ-HD300 Series OnlyRecorded-image Copy WJ-HD500 Series Only Alarm Search WJ-HD200 Series / WJ-HD100 Series Multiscreen DisplayTroubleshooting Problem Check item and Remedy ReferenceProblem Check item and Remedy Reference System Controller SpecificationsStandard Accessories Data PortPage 2004
Top Page Image Contents