Panasonic AWHE60SE, AWHE60SN, AWHE60HN, AWHE60HE manual WwManually adjusting the shutter speed

Page 18

Manual shooting (continued)

wwManually adjusting the shutter speed

The shutter speed can be set using two methods. One is a method that specifies the time (where a time such as 1/250 sec. is designated), and the other is a method that specifies the frequency (where synchro scan, 60.24 Hz*, etc. is designated).

When shooting a TV screen or PC monitor screen, the horizontal noise generated when the screen is shot can be minimized by adjusting the frequency to the screen frequency using synchro scan.

*: This describes when the AW‑HE60HN/AW‑HE60SN is used.

When performing the operations using the wireless remote control

Perform the adjustments on the Camera menu. For further details, refer to the [Shutter Mode] and [Step/Synchro] items on page 42.

When performing the operations using the controller

The procedure is the same as for “When performing the operations using the wireless remote control” in “Basic operations” (pages 32 to 39).

When the AW‑RP555 is connected:

1Press the [SHUTTER] button and turn its lamp on.

The shutter speed set ahead of time is selected.

2If necessary, press the [SHUTTER] button to turn its lamp off in order to return the shutter to the OFF setting.

qqHow to set the shutter speed using the AW‑RP555

1With the [MEMORY] button still held down, press the [SHUTTER] button.

The [PRESET] [1] to [5] and [6] to [10] buttons blink alternately.

2Press one of the [1] to [8] buttons or the

[10] [PRESET] button — whichever button corresponds to the shutter speed which is to be set.

Any of the shutter speeds in the table below can be set.

[When 59.94 Hz has been set as the unit’s frequency]

[1]	[2]	[3]		[4]	[5]

1/100	1/250	1/500		1/1000	1/2000

[6]	[7]		[8]		[10]

1/4000	1/10000	Synchro Scan			OFF

[When 50 Hz has been set as the unit’s frequency]

[1]	[2]	[3]		[4]	[5]

1/120	1/250	1/500		1/1000	1/2000

[6]	[7]		[8]		[10]

1/4000	1/10000	Synchro Scan			OFF

ppAny change in the shutter speed is reflected the next time the [SHUTTER] button is pressed and its lamp is

turned on.

ppWhen OFF is selected, the shutter will not operate

even when the [SHUTTER] button is pressed.

ppSelect the synchro scan setting on the menu.

ppThe shutter speed setting performed here is stored in the memory even when the power of the AW‑RP555 is turned off.

For further details, refer to the Operating Instructions of the AW‑RP555.

18

Image 18

Contents AW‑HE60HN AW‑HE60SN AW‑HE60HE AW‑HE60SE About copyright and licence Illustrations and screen displays featured in the manualTrademarks and registered trademarks AbbreviationsContents Before use WwOverviewWwRequired personal computer environment WwNetwork security WwDisclaimer of warrantyBefore use Usage restrictions英語版要入手 WwConcerning the plug-in viewer softwareSelect the shooting mode Basic shooting operationsSet the Operate switch on the controller to on How to turn the power on and offWwTurning the power on Pp Power on presetHow to turn the power on and off WwTurning the power offSet the Operate switch on the controller to OFF Selecting the units Selecting the shooting modes scene filesWwTypes of shooting modes WwHow to select the shooting mode Selecting the shooting modes scene filesAW ‑RP655 display AW ‑HE60 scene file Shooting QqUsing the zoom functionQqSwitching the direction or zoom speed QqChanging the camera’s directionMultiple color bands color bars are displayed Lens focus is not adjusted automaticallyUnit does not move Menu screen is displayedMore advanced operations WwManually adjusting the focus Manual shootingWwManually adjusting the iris Manual shootingWhen 59.94 Hz has been set as the unit’s frequency WwManually adjusting the shutter speedQq How to set the shutter speed using the AW‑RP555 When 50 Hz has been set as the unit’s frequencyWwManually adjusting the gain Press the OFF, LOW or HI buttonPress the Gain button to turn off its lamp Preset memories Set the memory recording mode Preset memoriesSet to the memory recording mode Hold down the Reset buttonWhen the AW‑RP555 is connected White balance adjustment WwWhite balance adjustmentQqAutomatic adjustment AWB AWB A or AWB B White balance adjustment Press the SET button for 2 secondsPress the AWC button QqAuto tracking white adjustment ATW QqManual adjustment Gain and B gain adjustment Press the M/IRIS button Black level master pedestal adjustmentWwBlack level master pedestal adjustment Press the IRIS - buttonBlack level master pedestal adjustment Press the Iris button several times to turn off its lampGenlock adjustment AW‑HE60S only WwGenlock adjustmentQqHorizontal phase adjustment Genlock adjustment AW‑HE60S only QqColor phase adjustmentPress the Mode button Genlock adjustment AW‑HE60S only Basic operations Table of operationsBasic operations Previous menuPress the  or  button to change the setting Jog dial main Jog dial LJog dial R QqProcedure for camera menu operation AW‑RP655 Press the Menu button to exit the camera menuMode button lights up at the BAR setting Press the Item button QqProcedure for camera menu operation AW‑RP555Perform one of the following steps to select the menu item Press the Menu button for 2 seconds to exit the camera menuQqProcedure for camera menu operation AW‑RP50 Camera OSDWwSetting the camera menu items Camera menu itemsWwTop Menu screen WwCamera screen When FullAuto is selected WwCamera screen When Manual1 to 3 is selectedCamera menu items WwContrast screen WwPicture 1/2 screen WwPicture 2/2 screen Ww16-axis color matrix WwSystem screen WwGenlock screen AW‑HE60S onlySqueeze Down CONV. Mode Squeeze, SideCut, LetterBoxWwOutput screen SideCutFormat Set screen QqChanging the formatFormat change check screen Format unchanged screenWwOther 1/2 screen WwOther 2/2 screen WwMaintenance screen WwFirmware Version screenQqConcerning initialization Default GatewayWwIP Network screen IP AddressFactory setting Menu Selection items FullAuto Manual1 Camera menu item tableCamera menu item table RGB‑NOR, RGB‑ENHControls and settings from web screen Operating system installed Web browser Controls and settings from web screenWwDisplaying the web screen using a personal computer Start the web browser of the personal computerControls and settings from web screen  Image Capture Size button Image Capture Size WwLive screen Single display mode Multi-Screen list box Multi-screen  Compression button Compression Camera button / Color bar button CAM/BAR  Power ON button / Standby button OSD Menu Operation  Operation lock button Op.Lock Main area IP video display area  Focus  Preset Zoom  Control pad and its buttons SnapShot  Full-screen displayWwLive screen Multi display mode WwSetup screen QqBasic screenCamera title 0 to 20 half-size characters Automatic installation of viewer software On, Off Basic button  Camera title display areaQqImage screen IP video settings Video over IP Video over IP Monitoring mode 16 9 resizeImage capture size QVGA, VGA Jpeg image settingsImage settings Transmission On, OffImage capture size QVGA, VGA Initial setting VGA Refresh intervalMulticast address Setting range 224.0.0.0 to Multicast port 1024 to 50000 Only even numbers can be setMulticast TTL/HOPLimit 1 to Image  Image Image adjust Preset positionImage adjust screen 仕向地による違い Contrast Contrast Mode Auto, Manual  Scene FullAuto, Manual1, Manual2, Manual3 Picture Chroma Level -3 to +3 AWBColor Matrix Normal, EBU, NTSC, User User Color Matrix Setup screen Preset position setting screen  Preset  Zoom  Speed With Zoom POS  Focus ADJ With PTZ Preset Setting Preset Speed 1 to  Limitation Setting Genlock AW‑HE60S only Horizontal Phase -206 to +49 System screen Output  Frequency 59.94Hz, 50Hz Other Images for which this setting is established Multi-screen setup  IP address To 128 half-size characters QqMulti-screen Camera title To 20 half-size characters QqUser mng Host auth. screen  Host auth  Access level  Host checkPriority stream  Priority stream ActivationStream type QqServer QqNetwork Network screen  IP networkDNS Port numbers already used 20, 21, 23, 25, 42, 53, 67, 68 System name 0 to 32 half-size characters Snmp screen Community 0 to 32 half-size characters  Location 0 to 32 half-size charactersSystem log screen QqMaintenance Error description  Time & date MAC address Product info. screen Model no  Serial no Viewer software installation counter  StatusDefault reset screen  Reset to the default Except the network settings Reboot Back up screen  Download Upload WpDisplaying the web screen using a mobile terminal  Pan/Tilt Resolution switching  Iris  Camera menu OSD menu operation  Tally lamp lighting status displaysCategory Display Description of error NTP-related error displaysLogin-related displays System log displaysLimiters WwBasic limiter operations Setting/releasing the limitersWwSetting the limiters Press the Menu buttonWwReleasing the limiters Setting/releasing the limitersWwResetting the limiters Pp Releasing the upper limit position of the movement rangeSafe mode WwConcerning the safe modeTrouble-triggered safe mode WwSystem requirements for a personal computer WwTrademarks and Registered TrademarksWwPrecautions when using Windows SymptomSolution 英語版必要 QqRestrictions 108109 Restriction 1 On the setup pages for some products Restriction 2 When using Windows 7 with some productsIndex XxA XxFIndex XxN XxTMemo Web Site http//panasonic.net Panasonic Corporation