Panasonic AWHE60SN How to turn the power on and off, WwTurning the power on, Pp Power on preset

Page 8

How to turn the power on and off

wwTurning the power on

When performing the operations using the wireless remote control

1Set all the power switches of the units and devices connected in the system to ON.

ppThis unit does not have a power switch.

When power is supplied to it, the status display lamp will light up orange.

The initial operation is then performed, and after this the unit is set to the standby mode.

2Press one of the [CAM1] to [CAM4] buttons on the wireless remote control to select the unit.

3Press the [ON/STANDBY] button on the wireless remote control for 2 seconds.

The POWER ON mode is established, images are output, and control can be exercised.

pp The unit’s status display lamp now lights up green.

Notes

ppIt takes about 30 seconds per unit for the initial settings operation to be completed. During this period, the unit cannot be operated.

(Status display lamp: light up orange)

ppWhen transferring to the STAND BY mode (Status display lamp: Orange)

The pan/tilt position is stored in the memory, and the pan/tilt unit is moved so that it points backwards.

ppWhen transferring to the POWER ON mode (Status display lamp: Green (after the initial setting operation is completed))

The pan/tilt unit is moved to the position which was stored in the memory when the transition to the STAND BY mode was made.

ppPOWER ON preset

The pan/tilt unit is moved to the setting, which was established immediately prior to the transition to the STAND BY mode, when the power has been turned on.

ppIf the power is turned off without transferring to the STAND BY mode, the pan/tilt unit position will not be stored in the memory or reflected in the POWER ON preset. The zoom position is stored using the setting established immediately before the power is turned off.

4If a multiple number of units are going to be used, repeat steps 2 and 3 as required.

The unit’s status display lamp blinks green when a signal matched by the remote control ID has been received, and it blinks orange when a signal that is not matched by the remote control ID has been received.

When performing the operations using the controller

When the AW‑RP655 or AW‑RP555 is connected:

1Set all the power switches of the units and devices connected in the system to ON.

ppThis unit does not have a power switch.

When power is supplied to it, the status display lamp will light up orange.

The initial operation is then performed, and after this the unit is set to the standby mode.

2Set the [OPERATE] switch on the controller to ON.

The POWER ON mode is established, images are output, and control can be exercised.

pp The unit’s status display lamp now lights up green.

Notes

ppIt takes about 30 seconds per unit for the initial settings operation to be completed. During this period, the unit cannot be operated.

(Status display lamp: light up orange)

ppWhen transferring to the STAND BY mode (Status display lamp: Orange)

The pan/tilt position is stored in the memory, and the pan/tilt unit is moved so that it points backwards.

ppWhen transferring to the POWER ON mode (Status display lamp: Green (after the initial setting operation is completed))

The pan/tilt unit is moved to the position which was stored in the memory when the transition to the STAND BY mode was made.

ppPOWER ON preset

The pan/tilt unit is moved to the setting, which was established immediately prior to the transition to the STAND BY mode, when the power has been turned on.

ppIf the power is turned off without transferring to the STAND BY mode, the pan/tilt unit position will not be stored in the memory or reflected in the POWER ON preset. The zoom position is stored using the setting established immediately before the power is turned off.

Before setting the [OPERATE] switch on the controller to ON, be absolutely sure to set all the power switches of the units and devices connected in the system to ON.

For further details, refer to the Operating Instructions of the controller.

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents AW‑HE60HN AW‑HE60SN AW‑HE60HE AW‑HE60SE Illustrations and screen displays featured in the manual Trademarks and registered trademarksAbout copyright and licence AbbreviationsContents WwRequired personal computer environment Before useWwOverview WwDisclaimer of warranty Before useWwNetwork security Usage restrictions英語版 要入手 WwConcerning the plug-in viewer softwareSelect the shooting mode Basic shooting operationsHow to turn the power on and off WwTurning the power onSet the Operate switch on the controller to on Pp Power on presetSet the Operate switch on the controller to OFF How to turn the power on and offWwTurning the power off WwTypes of shooting modes Selecting the unitsSelecting the shooting modes scene files WwHow to select the shooting mode Selecting the shooting modes scene filesAW ‑RP655 display AW ‑HE60 scene file QqUsing the zoom function QqSwitching the direction or zoom speedShooting QqChanging the camera’s directionLens focus is not adjusted automatically Unit does not moveMultiple color bands color bars are displayed Menu screen is displayedMore advanced operations WwManually adjusting the focus Manual shootingWwManually adjusting the iris Manual shootingWwManually adjusting the shutter speed Qq How to set the shutter speed using the AW‑RP555When 59.94 Hz has been set as the unit’s frequency When 50 Hz has been set as the unit’s frequencyPress the Gain button to turn off its lamp WwManually adjusting the gainPress the OFF, LOW or HI button Preset memories Preset memories Set to the memory recording modeSet the memory recording mode Hold down the Reset buttonWhen the AW‑RP555 is connected QqAutomatic adjustment AWB AWB A or AWB B White balance adjustmentWwWhite balance adjustment Press the AWC button White balance adjustmentPress the SET button for 2 seconds QqAuto tracking white adjustment ATW QqManual adjustment Gain and B gain adjustment Black level master pedestal adjustment WwBlack level master pedestal adjustmentPress the M/IRIS button Press the IRIS - buttonBlack level master pedestal adjustment Press the Iris button several times to turn off its lampQqHorizontal phase adjustment Genlock adjustment AW‑HE60S onlyWwGenlock adjustment Press the Mode button Genlock adjustment AW‑HE60S onlyQqColor phase adjustment Genlock adjustment AW‑HE60S only Basic operations Table of operationsBasic operations Previous menuPress the  or  button to change the setting Jog dial R Jog dial mainJog dial L QqProcedure for camera menu operation AW‑RP655 Press the Menu button to exit the camera menuMode button lights up at the BAR setting QqProcedure for camera menu operation AW‑RP555 Perform one of the following steps to select the menu itemPress the Item button Press the Menu button for 2 seconds to exit the camera menuQqProcedure for camera menu operation AW‑RP50 Camera OSDWwTop Menu screen WwSetting the camera menu itemsCamera menu items Camera menu items WwCamera screen When FullAuto is selectedWwCamera screen When Manual1 to 3 is selected WwContrast screen WwPicture 1/2 screen WwPicture 2/2 screen Ww16-axis color matrix WwSystem screen WwGenlock screen AW‑HE60S onlyDown CONV. Mode Squeeze, SideCut, LetterBox WwOutput screenSqueeze SideCutQqChanging the format Format change check screenFormat Set screen Format unchanged screenWwOther 1/2 screen WwOther 2/2 screen WwMaintenance screen WwFirmware Version screenDefault Gateway WwIP Network screenQqConcerning initialization IP AddressFactory setting Menu Selection items FullAuto Manual1 Camera menu item tableCamera menu item table RGB‑NOR, RGB‑ENHControls and settings from web screen Controls and settings from web screen WwDisplaying the web screen using a personal computerOperating system installed Web browser Start the web browser of the personal computerControls and settings from web screen WwLive screen Single display mode  Multi-Screen list box Multi-screen Image Capture Size button Image Capture Size  Compression button Compression Power ON button / Standby button  OSD Menu Operation Camera button / Color bar button CAM/BAR  Operation lock button Op.Lock Main area IP video display area  Preset  Zoom Focus  Control pad and its buttons SnapShot  Full-screen displayWwLive screen Multi display mode WwSetup screen QqBasic screenAutomatic installation of viewer software On, Off  Basic buttonCamera title 0 to 20 half-size characters  Camera title display areaIP video settings Video over IP  Video over IP Monitoring modeQqImage screen 16 9 resizeJpeg image settings Image settingsImage capture size QVGA, VGA Transmission On, OffImage capture size QVGA, VGA Initial setting VGA Refresh intervalMulticast TTL/HOPLimit 1 to Multicast address Setting range 224.0.0.0 toMulticast port 1024 to 50000 Only even numbers can be set Image  Image Image adjust Preset positionImage adjust screen 仕向地による違い Contrast Contrast Mode Auto, Manual  Scene FullAuto, Manual1, Manual2, Manual3 Picture Chroma Level -3 to +3 AWBColor Matrix Normal, EBU, NTSC, User User Color Matrix Setup screen Preset position setting screen  Preset  Zoom  Speed With Zoom POS  Focus ADJ With PTZ Preset Setting Preset Speed 1 to  Limitation Setting Genlock AW‑HE60S only Horizontal Phase -206 to +49 System screen Output  Frequency 59.94Hz, 50Hz Other Images for which this setting is established  Camera title To 20 half-size characters Multi-screen setup  IP address To 128 half-size charactersQqMulti-screen QqUser mng Host auth. screen  Host auth  Access level  Host checkStream type Priority stream Priority stream Activation QqServer QqNetwork Network screen  IP networkDNS Port numbers already used 20, 21, 23, 25, 42, 53, 67, 68Snmp screen  Community 0 to 32 half-size characters System name 0 to 32 half-size characters  Location 0 to 32 half-size charactersQqMaintenance  Error descriptionSystem log screen  Time & dateProduct info. screen  Model no MAC address  Serial no Viewer software installation counter  Status Reboot Default reset screen Reset to the default Except the network settings  Upload Back up screen Download WpDisplaying the web screen using a mobile terminal  Pan/Tilt Resolution switching  Iris  Camera menu OSD menu operation  Tally lamp lighting status displaysNTP-related error displays Login-related displaysCategory Display Description of error System log displaysLimiters Setting/releasing the limiters WwSetting the limitersWwBasic limiter operations Press the Menu buttonSetting/releasing the limiters WwResetting the limitersWwReleasing the limiters Pp Releasing the upper limit position of the movement rangeTrouble-triggered safe mode Safe modeWwConcerning the safe mode WwSystem requirements for a personal computer WwTrademarks and Registered TrademarksSolution WwPrecautions when using WindowsSymptom 英語版必要 QqRestrictions 108109 Restriction 1 On the setup pages for some products Restriction 2 When using Windows 7 with some productsIndex XxA XxFIndex XxN XxTMemo Web Site http//panasonic.net Panasonic Corporation
Top Page Image Contents