Panasonic AWHE60SN, AWHE60HN, AWHE60SE, AWHE60HE manual  Main area IP video display area

Page 60

Controls and settings from web screen (continued)

Main area (IP video display area)

The IP video of the connected camera will be displayed. While the tally lamp is on, the area frame will turn red. When the tally lamp is off, the display area will return to normal.

The camera image can be zoomed in and out by operating the mouse wheel inside the display area.

When the image is zoomed in, click within the display area at the desired new center position for the angle of view, then the camera image will appear centered around that position.

ppWhen the shooting scenes vary significantly, restrictions imposed by the graphics processing (GDI) of the operating system installed may give rise to a phenomenon called “screen tearing” (where parts of the picture are not displayed in synchronization) although this will depend on the personal computer used.

Notes

ppOn a personal computer running Windows, if “H.264 transmission” (page 67) is set to “On”, H.264 images and JPEG images can be displayed.

H.264 images will appear immediately after they appear on the Live screen (in single display mode). If it is set to “Off”, only JPEG images will appear.

ppOn a personal computer running Mac OS X, regardless of the “H.264 transmission” settings, only JPEG images will appear. (H.264 images will not appear.)

ppWhen “On” is selected as the “H.264 transmission” setting, the maximum speed at which the JPEG images are refreshed is limited to 15 fps regardless of whether H.264 images are being displayed.

ppThe speed at which the JPEG images are refreshed may be reduced depending on the network environment, performance of the personal computer used, subjects and number of access users.

ppA total of up to 14 users — both the users receiving H.264 images and the users receiving JPEG images — can access the unit at the same time.

However, depending on the settings for the “Bandwidth control(bit rate)” and “Max bit rate (per client)*”, the number of users who can access the unit may be limited to 14.

ppIf the maximum number of users who can access the unit has exceeded the upper limit, the “access exceeded” message is displayed.

ppWhen “Multicast” has been selected as the “Transmission type” (page 69) setting under “H.264 image settings”, the second and subsequent users receiving the H.264 images are not counted among the access users.

ppWhen “Disable” is selected for “Tally Enable” (page 50, page 81), the camera’s tally lamp will not light even when the tally signal is input. However, the area frame of the main area (IP video display area) will turn red.

60

Page 59 Page 61
Image 60
Page 59 Page 61
Contents AW‑HE60HN AW‑HE60SN AW‑HE60HE AW‑HE60SE Illustrations and screen displays featured in the manual Trademarks and registered trademarksAbout copyright and licence AbbreviationsContents Before use WwOverviewWwRequired personal computer environment WwDisclaimer of warranty Before useWwNetwork security Usage restrictions英語版 要入手 WwConcerning the plug-in viewer softwareSelect the shooting mode Basic shooting operationsHow to turn the power on and off WwTurning the power onSet the Operate switch on the controller to on Pp Power on presetHow to turn the power on and off WwTurning the power offSet the Operate switch on the controller to OFF Selecting the units Selecting the shooting modes scene filesWwTypes of shooting modes WwHow to select the shooting mode Selecting the shooting modes scene filesAW ‑RP655 display AW ‑HE60 scene file QqUsing the zoom function QqSwitching the direction or zoom speedShooting QqChanging the camera’s directionLens focus is not adjusted automatically Unit does not moveMultiple color bands color bars are displayed Menu screen is displayedMore advanced operations WwManually adjusting the focus Manual shootingWwManually adjusting the iris Manual shootingWwManually adjusting the shutter speed Qq How to set the shutter speed using the AW‑RP555When 59.94 Hz has been set as the unit’s frequency When 50 Hz has been set as the unit’s frequencyWwManually adjusting the gain Press the OFF, LOW or HI buttonPress the Gain button to turn off its lamp Preset memories Preset memories Set to the memory recording modeSet the memory recording mode Hold down the Reset buttonWhen the AW‑RP555 is connected White balance adjustment WwWhite balance adjustmentQqAutomatic adjustment AWB AWB A or AWB B White balance adjustment Press the SET button for 2 secondsPress the AWC button QqAuto tracking white adjustment ATW QqManual adjustment Gain and B gain adjustment Black level master pedestal adjustment WwBlack level master pedestal adjustmentPress the M/IRIS button Press the IRIS - buttonBlack level master pedestal adjustment Press the Iris button several times to turn off its lampGenlock adjustment AW‑HE60S only WwGenlock adjustmentQqHorizontal phase adjustment Genlock adjustment AW‑HE60S only QqColor phase adjustmentPress the Mode button Genlock adjustment AW‑HE60S only Basic operations Table of operationsBasic operations Previous menuPress the  or  button to change the setting Jog dial main Jog dial LJog dial R QqProcedure for camera menu operation AW‑RP655 Press the Menu button to exit the camera menuMode button lights up at the BAR setting QqProcedure for camera menu operation AW‑RP555 Perform one of the following steps to select the menu itemPress the Item button Press the Menu button for 2 seconds to exit the camera menuQqProcedure for camera menu operation AW‑RP50 Camera OSDWwSetting the camera menu items Camera menu itemsWwTop Menu screen WwCamera screen When FullAuto is selected WwCamera screen When Manual1 to 3 is selectedCamera menu items WwContrast screen WwPicture 1/2 screen WwPicture 2/2 screen Ww16-axis color matrix WwSystem screen WwGenlock screen AW‑HE60S onlyDown CONV. Mode Squeeze, SideCut, LetterBox WwOutput screenSqueeze SideCutQqChanging the format Format change check screenFormat Set screen Format unchanged screenWwOther 1/2 screen WwOther 2/2 screen WwMaintenance screen WwFirmware Version screenDefault Gateway WwIP Network screenQqConcerning initialization IP AddressFactory setting Menu Selection items FullAuto Manual1 Camera menu item tableCamera menu item table RGB‑NOR, RGB‑ENHControls and settings from web screen Controls and settings from web screen WwDisplaying the web screen using a personal computerOperating system installed Web browser Start the web browser of the personal computer Controls and settings from web screen WwLive screen Single display mode  Multi-Screen list box Multi-screen Image Capture Size button Image Capture Size  Compression button Compression Power ON button / Standby button  OSD Menu Operation Camera button / Color bar button CAM/BAR  Operation lock button Op.Lock Main area IP video display area  Preset  Zoom Focus  Control pad and its buttons SnapShot  Full-screen displayWwLive screen Multi display mode WwSetup screen QqBasic screenAutomatic installation of viewer software On, Off  Basic buttonCamera title 0 to 20 half-size characters  Camera title display areaIP video settings Video over IP  Video over IP Monitoring modeQqImage screen 16 9 resizeJpeg image settings Image settingsImage capture size QVGA, VGA Transmission On, OffImage capture size QVGA, VGA Initial setting VGA Refresh intervalMulticast address Setting range 224.0.0.0 to Multicast port 1024 to 50000 Only even numbers can be setMulticast TTL/HOPLimit 1 to Image  Image Image adjust Preset positionImage adjust screen 仕向地による違い Contrast Contrast Mode Auto, Manual  Scene FullAuto, Manual1, Manual2, Manual3 Picture Chroma Level -3 to +3 AWBColor Matrix Normal, EBU, NTSC, User User Color Matrix Setup screen Preset position setting screen  Preset  Zoom  Speed With Zoom POS  Focus ADJ With PTZ Preset Setting Preset Speed 1 to  Limitation Setting Genlock AW‑HE60S only Horizontal Phase -206 to +49 System screen Output  Frequency 59.94Hz, 50Hz Other Images for which this setting is established Multi-screen setup  IP address To 128 half-size characters QqMulti-screen Camera title To 20 half-size characters QqUser mng Host auth. screen  Host auth  Access level  Host checkPriority stream  Priority stream ActivationStream type QqServer QqNetwork Network screen  IP networkDNS Port numbers already used 20, 21, 23, 25, 42, 53, 67, 68Snmp screen  Community 0 to 32 half-size characters System name 0 to 32 half-size characters  Location 0 to 32 half-size charactersQqMaintenance  Error descriptionSystem log screen  Time & dateProduct info. screen  Model no MAC address  Serial no Viewer software installation counter  StatusDefault reset screen  Reset to the default Except the network settings Reboot Back up screen  Download Upload WpDisplaying the web screen using a mobile terminal  Pan/Tilt Resolution switching  Iris  Camera menu OSD menu operation  Tally lamp lighting status displaysNTP-related error displays Login-related displaysCategory Display Description of error System log displaysLimiters Setting/releasing the limiters WwSetting the limitersWwBasic limiter operations Press the Menu buttonSetting/releasing the limiters WwResetting the limitersWwReleasing the limiters Pp Releasing the upper limit position of the movement rangeSafe mode WwConcerning the safe modeTrouble-triggered safe mode WwSystem requirements for a personal computer WwTrademarks and Registered TrademarksWwPrecautions when using Windows SymptomSolution 英語版必要 QqRestrictions 108109 Restriction 1 On the setup pages for some products Restriction 2 When using Windows 7 with some productsIndex XxA XxFIndex XxN XxTMemo Web Site http//panasonic.net Panasonic Corporation
Top Page Image Contents