Adesso Series 2000 manual Plus Functions, Smoothing Mode, Units of Pressure, MAX/MIN Recorder

Page 4

Note: Do not tighten fittings attached to the pressure ports to a torque greater than 2Nm otherwise the pressure seals may be damaged.

HAND PUMP OPERATION (if applicable)

Use the T piece to connect the hand pump to the instrument’s + port and to the equipment being tested. Exhaust the system by turning the release valve on the hand pump anti-clockwise and set the fine adjustment threaded piston to mid range.

Close the release valve and apply pump action to the hand pump piston to generate the required approximate pressure. Fine adjustment of the desired pressure can then be made by rotating the threaded piston. The release valve may be used to vent the system. Note: The hand pump is capable of generating 7bar max. It is, therefore, essential that extra care is taken not to over-pressure the instrument.

A pump must not be used on models 2000P, 2020P and 2080P

PLUS FUNCTIONS

Models 2020P, 2021P, 2022P, 2023P, 2024P, 2025P, 2080P, 2081P, 2082P, 2084P, 2085P

SMOOTHING MODE

Press = key and the instrument continuously averages the last four measurements to give a more stable reading on the display. Press = key again to return to normal measurement.

UNITS OF PRESSURE

Press key to select required units of pressure. Chosen units will be saved when the instrument is switched off.

Please refer to the table on the back page.

The 20x0P 0-25mbar instruments cannot show the µbar or mmHg symbols on their displays. When switching the units on they are reading in µbar and so show no unit symbol. Pushing the autorange button will put the unit into mbar and show the mbar symbol. When reading in mmHg only the symbol Hg will show on the display.

This function will not operate while in store mode. Note: 2024P - 2084P

K = x 103 when using in H2O and Pa. M = x 106 when using in H2O and Pa.

MAX/MIN RECORDER

Press key to start. The instrument will display alternating symbols and current reading. Press again to display the

maximum temperature reading and symbol will be displayed. Press again to display the minimum temperature reading and symbol will be displayed. Press again to return to the actual temperature display.

Press X key to display the average temperature since the MAX/MIN

mode was activated and symbol will appear on display. Press

Xkey again to return to actual temperature display.

NOTE: To reset MAX/MIN recorder function switch the instrument off.

NOTE: Some functions may be inhibited while information is stored in either Auto, Manual or Max/Min modes. This is to prevent inadvertent parameter mixing whilst in any of the above modes. To re-activate these functions please delete any stored information by following the “Output of data” section.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 2000 Instrument Application Instrument OperationBatteries IP65/IP67 RatingBacklight DisplayOUT of Range ZeroingSmoothing Mode Plus FunctionsUnits of Pressure MAX/MIN RecorderSetting Internal Clock Preset Interval LoggingRange Lock Advanced FunctionsLeak Testing Setting UPOutput of Data AveragingWiring instructions Pressure Transducer SelectionModels 2024P, 2084P User Defined ScaleGERÄTE-ANWENDUNGEN Dies fällt nicht unter Garantie AnsprücheBatterien EIN/AUSSCHALTENHintergrundbeleuchtung AnzeigeBereichsüberschreitung NullpunktkorrekturAnschlüsse Handpumpe Falls VerwendetBedienung DER Erweiterten Modelle MITTELWERT-BILDUNGAutomatische Bereichseinstellung Zusätzliche FunktionenAUFZEICHNUNGS-MODUS Zeit EinstellenDatenausgabe MITTELWERT-MESSUNGENLECKSUCH-FUNKTION EinstellungenTypen FÜR Externe Druckmessumformer Modelle 2024P, 2084PAnschluss Externer Druckmessumformer VerkabelungsanleitungenAplicación DEL Instrumento Operación DEL InstrumentoPilas Protección IP65/IP67Fuera DE Rango Puesta a CeroPuesta a Cero Absoluta Modelo 2085PInstalación DE Tubo Funciones AdicionalesModo DE Alisamiento Unidades DE PresiónBloqueo DE Rango Funciones AvanzadasRegistro Logging Ajuste DEL Reloj InternoRegistro a Intervalos Predeterminados Salida DE DatosPromedio Verificación DE FugasConfiguración Realización DE UN EnsayoSelección DEL Transductor DE Presión Modelos 2024P, 2084PExactitud DE LOS Instrumentos Escala Definida POR EL UsuarioGarantia Mode D’EMPLOI Mise EN MarcheBatterie Niveau IP65/IP67Éclairage Dépassement DE CapacitéMise À Zéro Mise À Zéro DES Appareils AbsolusTuyau DE Raccordement Utilisation DE LA Pompe À MainFonctions Plus LissageBloquer LA Résolution Fonctions Plus AvancéesEnregistrer Comment Régler L’HORLOGE InterneMode Moyen Enregistrement PrérégléSortie DE Données Détection DE FuiteMise EN Marche Faire UN TestSélection DU Capteur DE Pression Instructions de câblagePrécision Echelle PersonnaliseeCalibration Applicazioni Dello Strumento Funzionamento Dello StrumentoValutazione IP65/IP67 PortataRetroilluminazione Fuori PortataAzzeramento Azzeramento AssolutoSistemazione Tubo Flessibile Funzioni PlusModalità DI Stabilizzazione Unità DI PressioneEstensione Dispositivo DI Bloccaggio Funzioni D’AVANGUARDIARegistrazione Regolazione DELL’OROLOGIO InternoFunzione Intermedia Uscita DatiProva Tenuta Acqua Predeterminazioni Prova DI PrestazioneSelezione DEL Trasduttore DI Pressione Modelli 2024P, 2084PScala Definita DALL’UTENTE Precisione Dello StrumentoReading Input PSI
Top Page Image Contents