American Power Conversion SYMSTRF-PD, SYMINIF-PD user manual Rear View of a Power Array

Page 19

Chapter 1 - Physical Representation

Rear View of a Power Array

The rear of a MiniFrame system is displayed below. The rear of a MasterFrame is similar. Each of the components are described in a section that follows:

System Enable Switch

The system enable switch regulates internal power to the Power Array. It does not power the load. When switched to the “on” position, the Power Array enters the load-disconnect operat- ing mode. When switched to “stand by” the Power Array is disconnected from incoming utility voltage. The load is not powered until the “power the load” command is entered into the PowerView interface.

Communication Interface Ports

The following three communication ports are provided: A remote PowerView cable port; an APC PowerChute Plus soft- ware interface port, and two battery extension frame com- munication ports. A 20’ RJ45 cable is provided with the Power Array for remote installation of the PowerView.

Smart SlotsTM Accessory Ports

APC manufactures a set of auxillary user interface accessories, called SmartSlotTM devices. Four SmartSlotTM installation ports are provided. SmartSlotTM interface options include:

Communication

Interface

Ports

Power Distribution

Unit (Optional)

System

Enable

Switch

Battery

Extension

Frame

Connector

REPO Wiring

Access Panels

νProtection and safe shutdown of multiple servers

νSNMP adaptor for accessing data via a network

νCallUPSTM - Initiates telephone notification of power event

νMeasureUPSTM - monitoring environmental conditions

νControl and monitor via modem

Note: Use only SmartSlotTM devices labelled “SymmetraTM compatible.”

REPO/Input/Output Wiring Access Panels

Wiring terminal blocks for input and output wiring, and for remote emergency power off (REPO) switch intallations are accessed through these panels. For use by a licensed electrian.

Power Distribution Unit Panel (Optional)

An optional power distribution unit provides output power receptacles and corresponding circuit breakers. The MiniFrame PDU provides one L6-30R receptacle (208V), two 5-15R recep- tacles (120V), and two L14-30R receptacles (120V/240V). The MasterFrame PDU provides three L6-30R receptacles, four 5- 15R receptacles, and three L14-30R receptacles. The PDU panel for both frame sizes are equipped with a panel circuit breaker.

Battery Extension Frame Connector

An optional Battery Extension Frame can be connected to the Power Array using this coupler. See the User’s Manual inluded with the Battery Extension Frame.

SmartSlotTM

Accessory

Ports

MiniFrame

Output

Wiring

Access

Panels

Input

Wiring

Access

Panels

Fig 1-8Rear View of a Mini Frame SymmetraTM Power Array System

1-4

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Syminif SYMINIF-PD Symstrf SYMSTRF-PD 990-7770A Revised 10/97 Radio Frequency InterferenceLife Support Policy Limited WarrantyTable of Contents Index Introduction Fig I-1MiniFrame and MasterFrame Fig I-2Functional Diagram of a SymmetraTMThank You SymmetraTM Overview Theory of OperationTransformer Power Processing SystemBattery Source Control/User InterfaceFig I-4On-Line Operating Mode Load-Disconnect ModeOn-Line Operating Mode Fig I-3Load-Disconnect Operating ModeFig I-6Bypass Operating Mode On-Battery Operating ModeBypass Operating Mode Fig I-5On-Battery Operating ModeImportant Information DefinitionsSafety Information Important Safety Instructions Symbols Used In This ManualTech Physical Representation 2An Empty MasterFrame grill covers removed Power Array Frame1A Fully Loaded MiniFrame grill covers removed Louvered Grill Covers Powerview User InterfacePower Module Battery ModuleInput Circuit Breaker Maintenance Bypass SwitchMain Intelligence Module MIM Redundant Intelligence Module RIMRear View of a Power Array Site Preparation BTU Output Space and Weight ConsiderationsTransporting Power Array to Installation Site Operating ConditionsSite Preparation Unpacking and Installing Frame Check For Damage Tools Required for SetupStorage of Battery and Power Modules Initial InspectionRemove the Frame from the Pallet Moving Battery & Power ModulesClean-UP Remove Packing MaterialsWiring Requirements & Procedures Repo Switch Wiring SymmetraTM WiringInput Wiring Output WiringInput Wiring Specifications Input WiringVoltage Jumper Procedure 5Input Hardwiring Configuration Input Wiring Procedure3Removal of Input Hardwiring Panels 4Input Wiring PathwayOutput Wiring Configurations Output WiringOutput Overcurrent Protection 8Output Wiring Configuration for 120V/240V Output Voltages Grounding Electrode Optional Output Wiring InstallationOutput Wiring Procedure Power Distribution Units OptionalCable Specifications Remote Emergency Power Off SwitchRepo Specifications Repo Switch InstallationVdc Repo Switch Connection Electrical Wiring TestElectrical Wiring Test/Checklist Contact Closure Repo Switch Connection4Input/Output Measured Voltage Multipliers 16Startup ScreenElectrical Requirements and Procedures Setting Up The Power Array 1Removing Cover Grills from Frame Setup of Power ArrayFrame Leveling Procedure Removing Cover Grills3Battery Alignment Grooves and Runners Installing the Battery ModulesProcedure for Battery Module Installation 2Location of Battery Module BaysProcedure for Power Module Installation Installing the Power Modules9Location of the MIM and RIM Installing the Main Intelligence Module MIMInstalling the Redundant Intelligence Module RIM Procedure for Main Intelligence Module MIM InstallationRemote Placement of the PowerView Installing the PowerView InterfaceWall Mounting the PowerView 13PowerView Wall Mounting Template SmartSlotTM Interface AccessoriesInstallation Test/Checklist Installation Test20Miscellaneous Status Screen 19Power Status Screen1SymmetraTM Power Module/Frame Capacities 21Power The Load Sequence23Initiate a Self-Test Sequence 25Power Down the Load Sequence24Return to On-Line Sequence System Setup PowerView Display 1The PowerView Interface PowerView DisplayPhysical Features of the Powerview PowerView FunctionsNavigation Keys PowerView LEDs1Power Array Display LEDs Color DescriptionStatus Startup ScreenTop-Level Menu Screen ControlLogging SetupAccessories DiagnosticsConfiguring & Operating the SymmetraTM Introduction Powering the Power Array1Startup Screen Review Status Conditions Powering the LoadsVoltage Status Screen Power Status Screen Battery Status ScreenLoad With Redundancy Status Screen Perform a Self Test Alarm Threshold Status ScreenMiscellaneous Status Screen Switching Audible Alarm Beeper Off Configure Shutdown ParametersConfigure Alarms Alarm Thresholds Selection ScreenEvent Log Screen Review Diagnostic InformationDiagnostics Menu Screen Review Logging MenuModule Replacement Returning Modules to APC Module ReplacementModule Failure Alarm Indicators Technical Support and Obtaining a Replacement ModuleReplacement Battery Module Verification Battery Module ReplacementRemoving a Battery Module Installing the Replacement ModuleRemoving the Power Module Power Module ReplacementReplacement Module Verification Replacement MIM Verification Installing the Replacement Main Intelligence ModuleInstalling the Replacement Redundant Intelligence Module Replacement Redundant Intelligene Module VerificationPowerView Display Messages PowerView Message Meaning Corrective Action Start-Up Min Runtime restored PowerView Message Meaning Corrective Action General StatusThreshol PowerView Meaning Corrective Action Message ModuleAlarm FailureFault PowerView Meaning Corrective Action Message BypassPowerView Message Meaning Corrective Action General Fault PowerView Display Messages Index Index SmartSlot accessories Toll free technical support
Top Page Image Contents