APC 6739380EN/JC Inverter On/Off commands, Language, display contrast and buzzer volume settings

Page 45

Inverter On/Off commands

These commands may be accessed only via the master display. When the "I/O" button is pressed, the series of

"Monitor" alphanumeric display (cont.)

Display for the inverter On/Off commands

screens in the figure opposite is displayed.

Note:

◗these commands do not concern the Static Switch Cubicle. The "I/O" button on the "static switch" cubicle produces the message:

COMMAND INVALID

STATIC SWITCH MODUL

◗the "I/O" button on a slave display monitor produces the message:

COMMAND INVALID

ON SLAVE DISPLAY

◗if the On/Off commands have not been validated (by the after-sales support technicians), pressing the "I/O" button produces the message:

or

START INVERTER ?

*=YES >=ESCAPE

*

initial screen

STOP INVERTER ?

*=YES >=ESCAPE

*

initial screen

Direct access to the function by pressing the "I/O" button .

This screen is displayed if the inverter is already off. It is a prompt to press the "*" button to confirm start-up. During start-up, the following screen is displayed:

PROCESSING

…

This screen is displayed if the inverter is on. It is a prompt to press the "*" button to confirm shutdown.

If the transfer to Mains 2 conditions are not correct, the following screen is displayed a few seconds:

COMMAND REFUSED

TRANSFER IMPOSSIBLE

Following confirmation of the command, the system automatically returns to the initial screen.

COMMAND INVALID

CONFIGURATION

◗ if a "Soft Tunor" session is in

 

 

 

COMMAND INVALID

 

progress (initiated by after-sales

 

 

support technicians), pressing the "I/O"

 

SOFT TUNOR

 

button produces the message:

 

 

 

 

 

Language, display contrast and buzzer volume settings

These settings may be accessed by pressing the "settings" button.

Display of the settings selection screens

The series of screens in the figure opposite is displayed.

LANGUAGE = ENGLISH

*=CONFIRM.

*

DISPLAY CONTRAST >=SELECT *=CONFIRM.

*

BUZZER VOLUME >=SELECT *=CONFIRM.

*

Direct access to the function by pressing the "settings" button.

Selection of the display language: English, French, German, Italian, Spanish, Dutch, Swedish, Finnish, Portuguese.

This screen is a prompt to set the display contrast by successively pressing the ">" button. When the setting is confirmed by pressing the "*" button, the system goes on to the buzzer.

When this screen is displayed, the buzzer automatically turns on. Press the ">" button several times to adjust the volume. After confirmation of the buzzer volume by the "*" button, the system automatically returns to the initial screen.

initial screen

6739380EN/JC - Page 45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Mgetm GalaxyTM 2 6739380EN/JC Contents Options System performance IntroductionSystem description System may also includeUp to 4 UPS identical ratings can be parallel-connected Different types of MGETMGalaxyTM 6000 systemsFrequency converter with battery backup power figure Static Switch Cubicle Isolation and protection devicesUPS or converter cubicles Main operating modes Normal operationOperation with Mains 1 down Battery time Operation with Mains 1 restoredBattery charge cycle Installation with an engine generator set Example of an installation with an engine generator setUPS shutdown or overload Frequency converters without redundancy Output voltage quality and continuityFrequency converters with redundancy Overload curveInverter cubicle Description of MGETMGalaxyTM 6000 cubicles250 to 400kVA UPS or frequency converter 450 to 500kVA UPS or frequency converterBattery cubicle KVA UPSFor a 250 to 300kVA UPS External maintenance bypass cubicle Static Switch CubicleControl panel Visible control panel Static Switch CubicleVisible control panel Mgetm GalaxyTM 6000 control panelBattery operation light Buzzer Operating problem lightLoad not protected light Load protected lightHidden control panel Light G battery charging Light F battery temperature outside tolerancesLight H inverter fault Light I battery dischargedSystem start-up Start-upSingle-unit or modular UPS Multi-bypass modular UPSGalaxy UPS Modular UPS with external maintenance bypassStart-up of a unit Parallel UPS systems with a Static Switch CubicleFrequency converters Start-up of a rectifier/chargerStart-up of an inverter Frequency converter without a batterySingle-unit or modular UPS system Frequency converter or multi-bypass UPSShutdown of a unit ShutdownShutdown of an inverter Shutdown of an rectifier/chargerSystem shutdown External maintenance bypassSingle-unit or single modular Modular UPSParallel UPSs with SSC Buzzer resetNo Mains With MainsMaintenance bypass AlarmsSignal transmission Signal receptionEnvironment information Standard information Media ContactsLED signalling box optional Additional information Media Contacts 15 optionalAdditional remote transmission board 30 6739380EN/JC Maintenance Maintenance configurationSingle-unit or single modular UPS figure Isolate the UPSs Frequency converter or parallel UPS with SSCVented lead-acid batteries Battery maintenanceAutodiagnostics Visual checkFunctional check Training centers Monitor alphanumeric display GeneralDisplay Lights 1 to Green lightsRed lights Alarm display and buzzer reset List of general alarmsDisplay of alarms Mains 2 Problem Check Frequency List of secondary alarmsBattery is currently being recharged Measurement system Current measurements Voltage measurementsDisplay of voltage measurements Display of current measurementsBattery measurements Frequency and power measurementsDisplay of power and frequency measurements Display of battery measurementsBattery test see figure opposite Language, display contrast and buzzer volume settings Inverter On/Off commandsDisplay for the inverter On/Off commands Display of the settings selection screensDisplay system configuration Display system configurationOptions LED signalling boxMedia Contacts 15 additional auxiliary transmission Tele-Monitor remote indications unitHarmonics filter and power factor improvement Vision displayRemote vision display Double bridge rectifier-charger Battery Temperature MonitorEmpty cubicles Mgetm GalaxyTM 6000UPSs standard input rectifier-charger50 6739380EN/JC
Top Page Image Contents