AGFA Printer manual Weekly Maintenance, Engine Storage AT the END of the Week

Page 23

:ANAPURNA L/XL

OPERATOR MANUAL

8.3. Weekly Maintenance

The weekly maintenance combines different small handlings, and a storage procedure:

- Clean the “Purge” and “Home” station Grid.

Use a filling-knife or a wide screwdriver, to cut off the cured ink that’s on the ribs.

(the “Home” grid can be taken out to remove the particles)

-Check the Purge station waste box and clean it, if hardened ink is present.

-Check the waste ink tank underneath the printing table; dispose the ink according to local government regulations. (Also see chapter 5.6.)

-Clean the “encoder” strip with alcohol. (Situated upfront on the main beam)

ENGINE STORAGE AT THE END OF THE WEEK:

ENCODER STRIP

-Move the carriage to the Purge position.

-Flush cleaning solution through the heads:

-First purge the 4 right heads (Lc, Lm, W1, W2), close them,

and in the second stage, purge the remaining 4 left heads (K, C, M, Y).

-Finally, open the 4 right heads again, and purge all 8 heads together now. By doing so, you’ll have the most optimal cleaning pressure.

-Switch all heads, and the Solution valve back to “I”.

-Set the Neg. Vacuum Pressure to “0”, leave the system for 1 minute

(Ink will now start dripping out the heads)

-Empty the sub-airtank by opening the tap (use a tube into a PE-bottle) (Sub-airtank is located at back of carriage)

-Restore the Neg. Pressure back to “-.034”

- Perform a Large Purge

SUB-AIRTANK

 

 

-Clean the Head Base Plate with a cloth

-Clean the heads with a fiber-free cloth.

-Check the nozzle’s on “weeping” or with a Jet Test.

-If all nozzles are present, the engine can be left in the Purge Position, with the Grid pushed backwards.

-Replace the towels in front of the Purge grid, and check/clean the whole Purge station environment, the front of the UV-lamps might need some cleaning too.

-Clean the Quartz plate of both UV-lamp houses with alcohol. (underside of lamps)

AB]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]23]8/09/2006]

Image 23
Contents Anapurna L/XL Table of Contents Safety Instructions System Dimensions Printer Overview and FeaturesFront view, parts & locations Rear view, parts & locations Cover Open Sensor Head Carriage view, parts Signal tower Color Sequence Head technologyPacking Anapurna UV Curable InkGeneral information Color gamutSub Ink Tank Ink CircuitMain ink tanks Auto ink supplyRead out How to make changes 2-Way valves Ink supply by means of negative pressure Printing headsEncoder Test can be found in the Test menu Waste Tank Ink Refill System what can go wrong…UV Curing System Curing setup and sequencesSettings in software Lamp Type Cure Default, Set or BothUni- and Bi-directional printing By default, Full power should be used whenever possibleBelt Tension control Printing TableReplacement of Conveyor belt MaintenanceDaily Maintenance Nozzle check/purge MaintenanceLittle purge Cleaning the failing heads Engine Storage AT the END of the Week Weekly MaintenanceEngine is NOW Ready for a Long Stand Still Long Stand StillEngine is NOW Ready to Print Again Auto Feed System Media SetupRoll to Roll Take-Up Motor Box Rigid Support tables Rigid MediaAB298/09/2006 Head Base Height Control Automatic Head Base Height SetupMm Gap Set Top forward and Left Margin Anapurna Control ProgramControl Program Menu Display Printing ProgressSetup Parameter Menu Good AB358/09/2006 AB368/09/2006 Test Menu Carriage will move slowly back to the Home position To end this test, select Reset Test in the same menu,Carriage must be moved to the home position first Printing an imagePreparing an image Preparing the AnapurnaPrinting the image Purge function on the printing Cancel a printWhile printing, press S and Y, the print is then cancelled Image size/border Wasatch Rip Tips & TricksPrinting on heat sensitive media Media corners lift a bit up rigid media